Hasselblad 500C Viewfinder + Calibration

[12557]

Hi everyone,

I recently got a Hasselblad 500C (1966) from a friend for a very good price. When I inspected the camera, I noticed that the focusing screen had been installed incorrectly and rotated.

I’m a fairly experienced precision mechanic, so I carefully removed the four screws, disassembled the screen assembly, and reinstalled everything in what seemed to be the correct order and orientation.

Inside the finder assembly I found the following parts:

• a ground glass focusing screen
• a line/grid screen
• a spring frame
• a metal retaining frame
• and additionally a ~0.8 mm thick plexiglass spacer

The plexiglass spacer confused me a bit, because I’m not sure if it actually belongs there or if it was added later.

So my questions are:

• What is the correct order of these elements in a Hasselblad 500C?
• Where should the spacer go, if it belongs there at all? Or should it be removed?
• How do you properly adjust the focus afterwards so that the ground glass matches the film plane? Is there a simple trick to check or calibrate it?

Thanks a lot for your help — I really appreciate the knowledge and experience in this forum.

 

[loccdor]

Is this helpful?

https://phsc.ca/repair/Hasselblad/hasselblad_camera_500C.pdf

Welcome to Photrio!

 

[loccdor]

How do you properly adjust the focus afterwards so that the ground glass matches the film plane? Is there a simple trick to check or calibrate it?

Taping a ground glass on the film gate of the camera back, seeing if the focus point on both glasses agree with a magnifier, using a shallow depth of field lens with a high contrast target, is one way to do it.

If someone put a spacer there they likely did it for a reason (to fix the focus offset). I don't see anything in the service manual that looks like a plexiglass spacer.

 

[12557]

Hey @loccdor Thank you so much! I know this pdf and the strange thing is there is no plexiglass spacer the question is is my glas a original one?

And Should I tape the ground glass directly onto the metal edge? Is that where the film plane is?

Greets!

 

[loccdor]

I've never touched a Hasselblad, but I have a feeling this spacer was added by someone trying to make the focusing screen more accurate. Do you have a picture of it?

 

[12557]

Yes ia have

 

[John Salim]

Taping a ground glass on the film gate of the camera back, seeing if the focus point on both glasses agree with a magnifier, using a shallow depth of field lens with a high contrast target, is one way to do it.

If someone put a spacer there they likely did it for a reason (to fix the focus offset). I don't see anything in the service manual that looks like a plexiglass spacer.

Taping a ground-glass is something you can't do with a Hasselblad body, because the magazine is the gate !
You'd need a focussing screen attachment to do this ( ... the type usually used for SWC bodies )

John S

 

[12557]

Hey John! I thought so. Can you tell me what such a ground glass looks like?

 

[gorbas]

Hi, I have similar issue with 1000F model. I'm looking for proper procedure to install focusing screen with "spring spacer" under it.
Specifically, how to evenly screw 4 screws that determine screen height.
Is you plexiglass spacer (just a thin "frame"on the picture?) looks like simple shim to me.
Recently, they have been using full plexiglass inserts (with pattern similar to fresnel lenses") under regular Hasselblad screen with Fuji Instax film "polaroid" backs, to offset difference in focusing plane. I don't think that is the case with your camera.
This is the newest ground back adapter

 

[12557]

Oh, that adapter is interesting. Where can you buy it and how much does it cost?

Yes, exactly — it is just a very thin frame, but I don’t know where it belongs or if it should be there at all.

According to the Hasselblad manual and the exploded diagram, it actually shouldn’t be there.

 

[gorbas]

Oh, that adapter is interesting. Where can you buy it and how much does it cost?

Yes, exactly — it is just a very thin frame, but I don’t know where it belongs or if it should be there at all.

According to the Hasselblad manual and the exploded diagram, it actually shouldn’t be there.

Can you have sharp infinity in viewfinder (let's say over 250m+ distance) if you put in this order: Plexiglass shim, spring washer frame, focusing screen, the frame, screws. If not, take out plexiglass shim first adjust height with adjusting screws up or down. How to do it right? No idea?
Will be nice to have some original instruction.
Issue here is how to evenly tighten screws to have spring frame hold focusing screen at right height and parallel.
If on processed negative you have infinity in focus, than you most likely do not need this adapter.

You can find them maybe in your local second hand photo store or Ebay.
They are not cheap, there are also some made in China, not sure how good they are?

 

[loccdor]

How do distant trees look in the ground glass at infinity? Assuming you have a lens for it.

 

[12557]

Exactly, thanks for the tip. That’s exactly how I did it.


So far I have adjusted and calibrated everything and then checked whether I can get infinity focus at long distance, and I can get everything perfectly sharp.





My order was the following:





metal washer spring frame → Fresnel screen with focusing aid → grid screen → frame → four screws





The result was best when I tightened the four screws relatively firmly and evenly.


I actually think that whether it is slightly tilted probably doesn’t matter too much, as long as the center is sharp, because for the viewfinder preview that should be the most important part.


When you say second-hand, do you mean other focusing screens?

What exactly do you mean I should search for on eBay?

Thank you guys!