The Great Sensitometer Shootout....

[ic-racer]

vintage of gear.

?

The ESECO units tested here are new production.
http://www.eseco-speedmaster.com/sl-2.pdf

 

[ic-racer]

This is a scaled composite of the spectral sensitivities of FP4, Tri-X and TMX. Based on these curves I'd predict all 4 sensitometers will give useful information about the speed differences between the three.

 

[Rafal Lukawiecki]

Ok, try this. Make a test strip that goes to maximum black on the paper but keep blasting it with additional strips of exposure. Lay the processed and dried paper on an opaque surface and check for the darkest strip, now hold it up to the light. You can now see all those darker bands. So, even how you hold a print to view it influences D-max.

IC, I value your posts very much, and I have always learned something from you, thank you. I have done what you have just suggested, but I am afraid I cannot see what you have seen. I have a few test strips, on MGWT FB, in front of me. All exposed using different grades. Each has a fairly full range, from paper base white, to DMax. All the strips that have been "blasted" beyond maximum black read the same on my reflection densitometer, and, unfortunately, I cannot distinguish their boundaries even under a strong light. What I am saying is that my reflection densitometer seems to indicate a DMax value at the very level at which my eye cannot do better.

I am aware that we perceive reflected shadows and highlights in a relative way, depending on the surrounding environment and illumination, very much. This would be the same, I feel, to how I would see shadows and highlights in a transmission scenario, when looking at a negative, in various environments and illumination. However, in both cases, I find that the densitometer, in reflection or transmission mode, seems to agree with what my eye sees, given enough illumination or more.

I am sure I must be missing a point you were trying to make, or perhaps I am not seeing the effect you have described. Many thanks for your suggestions.

 

[Photo Engineer]

Rafael;

That was part of my point above. In many cases, where a reflection densitometer will show the same Dmax, transmission results might vary.

In these cases, you may see changes in contrast or shoulder density of the varying reflection samples.


PE

 

[ic-racer]

I cannot distinguish their boundaries even under a strong light.

Again, it is just an interesting 'example' but did you hold them up to the light, so light shines through the paper?

 

[ic-racer]

Also, just to further emphasize that reflection densitometry results from photographic papers can be influenced by many variables, here is a quote from Proposed American Standard Method of Processing for Sensitometry of Photographic Paper—Z38.2.3*
Nothing wrong with using reflection densitometry and there is usually no difficulty with mid zones and slopes (as PE pointed out) but if you are using reflection densitometry in your darkroom to include a reliable D-max in the curves, you need to make sure you account for all the variables to get useful results.

4. MEASUREMENT IN DENSITY
The sample should be illuminated at an angle of 45 degrees to the surface and the density
measured normal to the surface. Samples having a pronounced surface characteristic should have the densities read first in one position perpendicular to the viewing axis. Then the specimen should be rotated through an angle of 90. degrees about the viewing axis and the density measured again. The two values thus obtained should be averaged and recorded as the density for that measurement.

 

[ic-racer]

I don't know how many people are familiar with Todd and Zakia's book "Photograpic Sensitometry" but when I was in graduate school it was my 'bible' for photographic technique.

Anyway I would like to quote from the book a passage that further emphasizes my technique of visual estimation of paper response, rather than reflection sensitometry of paper.

Information about log E paper ranges needs to be reliable. Such information is best obtained by a test in the actual printing conditions, rather than relying on manufacturer's data which are only representative of a product. This information can be obtained by printing a negative step tablet in a standardized way with a controlled light source and at a know magnification if a enlarger is being used. A visual examination of the print of the step tablet is usually sufficient to establish of the range of log E over which the paper responds."
.

 

[ic-racer]

So, not to dissuade anyone from employing reflection densitometry, I wanted to point out that in my darkroom it has no role in matching paper to negative.

With that I want to conclude the test of the ESECO sensitometers and now I'll package up Jeff's unit and send it to him. Thanks Jeff for the opportunity to do these tests.

 

[Dismayed]

For the two tests mentioned here, it does not matter they all work equally well. I might go for the LED one, but really whatever you can get for less than $100. Even an enlarger will work. These ESECO units list for $750 but we got them for $25 on ebay.

For "Beyond The Zone System" testing; I don't know. You have to buy into that system and it involves (from what I gather) matching paper to negative with the curves. I'm not a fan of that method of working but that is not to say it is not a good system or that people should not use it. I have used multigrade paper and variable filtration since 1974 and prefer working the negatives up as I print them with trial and error. Also, I don't have the workbooks or software for the system, so I can't test it with these sensitometers.

If I were to take a guess, I'd say that none of these units will work with that system because some of your photographs will be at exposures longer than 1 second or shorter than 1/1000 second. None of these 4 units duplicates how your film in your camera responds to daylight scenes one might photograph. Again, that is just my guess and someone should test how that system responds to different sensitometers. Of course the reflection densitometers used for reading the paper will be a whole other can of worms. I don't own a reflection densitometer and have turned them down when offered to me for free. I don't think they are very reliable at reading the glossy photographic papers I use. They are designed for the graphic arts industry.

Thanks. I just run simple film tests - no BTZS measurements. A friend used to lend me a Heiland desitometer, but it has, unfortunately, disappeared.

 

[Bill Burk]

I would use the reflection densitometer of my TR524 to graph paper and developer tests... if I felt it was necessary. I've told the story several times how I short-circuited my need to do the paper tests because I found two edge-case negatives...

But it's not a bad idea to graph your paper so you know what you are getting.

Next plan... to check for optimum toning times...

 

[DREW WILEY]

What do you mean by "optimum" toning? Simply DMax with selenium? Because toners are also used for, well, "tone", actually meaning hue in this case. And when used more than one at a time, both the perceived and measured DMax are affected. So guess you'll have to narrow your parameters to a specific paper and developer (and specific dev time, temp, and concentration) if you want specific results. Even the color mix on VC papers is a factor.

 

[Bill Burk]

What do you mean by "optimum" toning? Simply DMax with selenium?

Yes, exactly. Toning for DMax with Selenium on Galerie.

I understand this might not necessarily be toning for the longest archival benefit, as the DMax may come at a point when not all Silver has been converted to Silver Selenide. But that's what I was thinking of doing.

 

[ic-racer]

Just an observation for those who seek D-max.

Another quote from Todd and Zakia:

In connection with the development of the ASA negative speed method, an experiment was done to determine the print characteristics for the images preferred by the panel of observers. In general, it was found that only a part of the paper curve was used in making excellent prints. Specifically, almost no preferred print contained the maximum density of which the paper was capable. The darkest shadow was quite uniformly found at a point on the D log E curve well below the maximum....

 

[Photo Engineer]

Does no one hear me?

Paper (reflection print material) cannot go over about 2.2 in density and varies from 1.8 to 2.2 depending on surface quality. Reflection densities in high regions are therefore hard to read.

Also, read up on "goniophotometry". This describes the variation in density of reflection print materials as a function of the angle of measurement or viewing. I have done a lot of work on all of the above.

If you want to talk about densitometry, please leave out reflection!!!!! There does not seem to be enough understanding of this topic.

PE

 

[ic-racer]

I'm just bumping this thread. I had some e-mails on the topic.

 

[ic-racer]

In this thread I wrote "I don't own a reflection densitometer," however, for the sake of keeping honest, I now have one, it was sent to me as a gift (thank you!).

 

[Stephen Benskin]

I did some testing of the Gamma-Lambda Effect many years ago. Using an EG&G calibrated sensitometer, I made 4 exposures using a tri-color red, green, and blue filter, and one without any filters. Here's what I found with Tri-X.

 

[ic-racer]

Those effects were accounted for by using the same colored light for each of the two comparison exposures during the development/contrast tests.

 

[ic-racer]

Thank you PhotoBucket, all the pictures and graphs from this thread are gone. Maybe I have copies I can re-upload...

Found this image.

The conclusion "A two minute reduction in development time gave the same change in slope (change in contrast) irrespective of sensitometer"

 

[ic-racer]

The sensitometers used in the test

 

[ic-racer]

All 4 sensitometers correctly identified FP4 as being the same number of stops slower than Tri-X.

 

[ic-racer]

All 4 sensitometers indicated the same change in Tri-X contrast for a 2 minute reduction in development time

 

[reneboehmer]

This is a modern example of the gamma lambda effect, I measured today with a SensiX blue-green sensitometer. Film used was Fp4+. It shows the contrast change of the material between green and blue exposure.

 

[Bill Burk]

Nice.
I haven't tried gamma lambda tests. I believe they are important for color separations, getting gray balance right by developing the blue filtered (yellow plate) separation longer.
And for the sensitometer shoot out they show you that the blue/green sensitometers can be reasonably used for process control, maybe best by using the green filter if you can.

 

[ic-racer]

Ok, so I see another image missing from this thread. This spectral sensitiviy composite. With the green marked (as Bill suggested above).