Zone VI VC enlarger

tequilabong · Jun 23, 2009

Hello......

How many Zone VI VC head users are members here? I recently started using one and would like to start a users group. Anyone interested???

Thanks.

Gordo

TimVermont · Jun 24, 2009

If you can flip this to a poll, you'll get more answers. I have a VC Type 2 with custom glass carriers made with Denglas, and fortunately, a very bright head.

cowanw · Jun 24, 2009

I am in

Anscojohn · Jun 24, 2009

tequilabong said:
Hello......

How many Zone VI VC head users are members here? I recently started using one and would like to start a users group. Anyone interested???

Thanks.

Gordo

******
Count me in.

payral · Jun 24, 2009

I am in too with a type 2. You can see it there:
http://pagesperso-orange.fr/payral/laboratoire/laboratoire.html

resummerfield · Jun 24, 2009

I have a VC Type 2, also with a custom glass carrier.

ron mcelroy · Jun 24, 2009

Another user with of a Type 2 VC head.

What kind of custom glass negative carriers are you using?

TimVermont · Jun 25, 2009

I have two pieces of Denglas, hinged at the back, drilled on one side with two holes, matching pins on the other (setup mates with my existing Kodak film punch) and a set of matte-black masks from 35mm to 5x7 (actually 13x18cm). For casual printing, I put unpunched film up against the pins, close the sandwich, and put the mask on top of the upper glass plate. I've used it for many years with no complaints.

Richard T Ritter · Jun 26, 2009

It looks like the photo below come with optical glass. They are custom made I have one available for the type II enlarger.

rmann · Jun 26, 2009

I have a VC type 2. I have a Beseler 5x7 Negaflat carrier that I use. They are not common, it fits and does a nice job of holding a negative flat.

trudee yama · Jun 26, 2009

I too have a Zone VI VC enlarger and love it. Purchased used, the original owner bought one of the first built. Still works great! Have only had to replace the guiding track on the column, that was quite the job. Can't seem to stop all light leaks around the head, but they dont seem to interfere with end results.

resummerfield · Jun 26, 2009

Richard T Ritter said:
It looks like the photo below come with optical glass. They are custom made I have one available for the type II enlarger.

This is the one I had Richard make for me. It works well, but if I were designing another one, I would incorporate alignment pins for my Kodak punch, just as TimVermont has done.

I seldom do masking, but when I do I use a setup similar to what TimVermont uses.... one piece of glass with a pin-set taped on, and covered with another piece of glass which is slightly narrower to miss the pin-set.

tequilabong · Jun 28, 2009

Ok, looks like we have quite a few users........

Is there a way to set up a group just for this purpose???

Forgive my cluelessness!!

Thanks.

gordo

tequilabong · Jun 28, 2009

Ok, I guess I'm not that clueless.........Was quite easy to make up the group.

Here it is.......Hope we can help each other!!

(there was a url link here which no longer exists)

Eric Mac · Jun 28, 2009

8x10 enlarger

I recently landed an 8x10 head for the Zone vi enlarger. Does any one have an extra (not likely) chimney and carrier or at least a picture with dimensions and/or details?

Thanks
Eric

memorris · Jul 1, 2009

I just bought a Zone VI type 2 enlarger, count me in.

Anscojohn · Jul 1, 2009

Eric Mac said:
I recently landed an 8x10 head for the Zone vi enlarger. Does any one have an extra (not likely) chimney and carrier or at least a picture with dimensions and/or details?

Thanks
Eric

*******
Are you going to be printing 8x10 negs? If not, the chimney is not a necessity.

edpierce · Jul 9, 2009

lensboards

Anyone have a type 2 lensboard with a 42mm hole?

Willing to trade a mf neg carrier for it.

Anscojohn · Jul 9, 2009

Eric Mac said:
I recently landed an 8x10 head for the Zone vi enlarger. Does any one have an extra (not likely) chimney and carrier or at least a picture with dimensions and/or details?

Thanks
Eric

*******
I have a chimney I am not using; but plan to hang on to it, just in case. I adapted the 8x10 head for 5x7 and smaller.

mike c · Jul 9, 2009

I have a zone vi type I,ah does that count? Have too use graded paper ,any body have a spare vc head for sale. or even a type 54 grid.

Mike

voceumana · Jul 10, 2009

edpierce said:
Anyone have a type 2 lensboard with a 42mm hole?

Willing to trade a mf neg carrier for it.

I got a good deal on a Type II last December (2008). Needed a 50mm lensboard; Calumet had lots of 25mm lensboards in stock, & drilled it to 50mm. Contact them--they might have 42mm stock or be able to drill one for you.

Charlie Strack

RJS · Jul 10, 2009

I used to covet the Zone VI until I read of all the problems. I passed on a new one a few years back being sold at Calumet store. The 'BEST DAMN ENLARGER IN THE UNIVERSE" is apparently ok, but forall I have heard no better than Omega or Beseler. Having never seen them it sounds to me as if a couple of european brands are probably better, stuff like Durst etc. but the prices here used to be enormous. After all, it's just a projector for different sizes of film. Basically a really simple machine.

ron mcelroy · Jul 10, 2009

While I own and like my Type II, I don't recommend them. The lack of parts, acessories and support compaired to Beseler and Omega makes them undesirable in my opinion.

TimVermont · Jul 13, 2009

I've repaired and aligned an entire lab full of Omega D Series enlargers. They all have three things in common: poor quality screws, light leaks and few built-in provisions for alignment. My type II has none of these problems.

jeroldharter · Jul 17, 2009

Zone VI VC Head for Beseler

I recently picked up a Zone VI VC head for Beseler without any instructions so I am trying to figure out how to connect everything. It came with the Variable Contrast controller that connects to the head with the telephone cord but nothing else. It does not have a separate power supply.

Is the power supply in the head itself?
Do I just need a power cord with a female end to plug into the top of the head? Is that "Power" cord for a heater?
What is the mouse-like connection port for?

Thanks.

Zone VI VC enlarger

Attachments

Privacy & Transparency

Privacy & Transparency