Transformer question

Trond

Subscriber
Joined
Jul 21, 2004
Messages
858
Location
Harestua, Norway
Format
Multi Format
The transformer for my IFF Ampliator enlarger has two switches on it. The first one is obviously the power switch, but the second one doesn't make anything obvious happen. It can be on or off and everything behaves the same.

The switch is wired up to something inside, but I don't know much about electronics to make any sense out of it.

Does anyone have an idea?

Trond
 

domaz

Member
Joined
Nov 2, 2007
Messages
572
Location
Tacoma, WA
Format
Multi Format
Can't tell from that picture. Is that a relay to the left of the transformer? I hope your not powering your enlarger on with the case open- that transformer would probably blow you out of your chair.
 

Ian C

Member
Joined
Feb 8, 2009
Messages
1,264
Format
Large Format
On some DeVere power distribution boxes, such as the one for the 5108, there are two switches. The first is marked “Mains: On/Off” for power on or off.

The second is marked “Stabilised/Unstabilised.” Selecting “Unstabilised” sends unstabilzed line current directly to the Dichromat head.

Choosing “Stabilised” sends the power through a voltage stabilizer, if one is connected to the appropriate connector on the power supply, and then to the Dichromat head. This keeps the bulb voltage constant for consistent print-to-print color work.

The 5108 doesn’t use a transformer on the US and Canada version since it uses 4 300-watt 120-volt ELH bulbs that match the input line voltage.
 
OP
OP

Trond

Subscriber
Joined
Jul 21, 2004
Messages
858
Location
Harestua, Norway
Format
Multi Format
domaz said:
Can't tell from that picture. Is that a relay to the left of the transformer? I hope your not powering your enlarger on with the case open- that transformer would probably blow you out of your chair.
Click to expand...

There is a relay to the left of the transformer. The transformer is connected directly to a wall socket, and it has another plug that goes to the timer. I think the relay is used to switch the lamps on and off. It has some large components at the back which looks like resistors.

I suppose it doesn't matter what the switch is for when it doesn't do anything!

Trond
 

ic-racer

Member
Joined
Feb 25, 2007
Messages
16,619
Location
USA
Format
Multi Format
Base on the picture this is what I think:

The transformer converts 220v to 48v at 700watts maximum for the bulb
The resistors drop that lower for some other thing on the enlarger. Like an indicator light or the fan.

Are there wires to the lower switch? Where do the wires come from? Maybe it is to turn on or off the alternate supply , like to turn off any indicator lights.
 

MPandolfo

Subscriber
Joined
Dec 12, 2006
Messages
59
Location
Santiago
Format
35mm
ic-racer said:
The resistors drop that lower for some other thing on the enlarger.
Click to expand...

Those resistors are more likely part of a snubber circuit.
Note the capacitors associated with them.
Possibly, that circuit is there to protect the lamp or the relay contacts.
 
Last edited by a moderator:
OP
OP

Trond

Subscriber
Joined
Jul 21, 2004
Messages
858
Location
Harestua, Norway
Format
Multi Format
MPandolfo said:
Those resistors are more likely part of a snubber circuit.
Note the capacitors associated with them.
Possibly, that circuit is there to protect the lamp or the relay contacts.
Click to expand...

This sounds plausible. The power supply makes a clicking sound when the lamps turn on and off, and I suppose that comes from the relay. The filter scale lamps didn't work when I got the enlarger, and in the end I connected a small external power supply to the head just for the filter scale lamps. Perhaps the the second switch is there just to turn on and off the these lamps as ic-racer suggests. I will open it up again and check where all the wires go.
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…