setting up a camera bag

[EASmithV]

hello,

when you are putting your older large format lenses in the camera bag, and there are no lens caps for them, would you rather:

A. make a mat board sleeve for them to give them a hard sided case to then fit into padded dividers,

or

B. Just drop them into the padded dividers because the dividers are soft and won't damage the lens


I am leaning toward making mat board sleeves, but I don't want to put excessive wear on the lenses or even damage them any worse than just padding would. I am particularly worried about the rear elements because they are not recessed anywhere near as much as the front elements are. Also, the mat board option seems like it would generate more dust?

 

[tessar]

I use padded dividers, also the right size caps -- took some hunting, not too much -- for the rear elements on the lenses. I think the mat board would make for more dust, as you suggested.

 

[removed account4]

camera wraps work well eric
also those beer buddies, you know the foamy things to keep your beer from
making yourhands too cold ...

 

[bdial]

The disposible food containers made by Glad and the others work well.
On most of the square ones, the sides are tapered, depending on the size of your board it will (may) suspend the lens above the bottom.
The round ones work nicely for non-mounted lenses. Plus, they are light weight, and cheap.

Grocery stores are also a good source for slip-on caps, just find one that fits, and buy the can of whatever it's on, leave it in the food pantry collection box if it's not on your "food" list. (though probably not rear caps for most LF lenses)

 

[onepuff]

I would much rather source some proper lens caps that fit rather than make something from board as these will likely rub and generate dust and grit to scratch the front and rear elements. Front and rear caps are easily available and relatively cheap for a multitude of fitting sizes so why potentially ruin an expensive lens for little saving.

 

[shutterfinger]

I use Foam Wrap , 1/8 inch thick, example: http://www.amazon.com/Foam-Wrap-feet-inches-wide/dp/B005K0A9WY to wrap my LF lens in. I keep them folded, lens side in, in the camera case when the lens is in use. I also take care to keep the wrap clean when changing lens.

 

[hdeyong]

I grab any older and well-worn wash cloths and those smaller hand towels that are around the house. Nice and soft, largely lint free, and when they get a little dusty, toss 'em in the wash. Also, really handy to have for a quick wipe down after a little rain shower, or for perspiration, or whatever. My bag's got two or three of them in it all the time.
If one gets a hole or a tear, I then put it in the garage to use there, because they shed threads like crazy.

 

[Kevin Caulfield]

camera wraps work well eric
also those beer buddies, you know the foamy things to keep your beer from
making yourhands too cold ...

They're called "stubbie coolers", John. At least that's what they're called here in Australia.

 

[250swb]

The plastic end caps from cardboard postal tubes work well. They don't need to fit perfectly, but one on the front, one on the back, and a rubber band over the top to stop them falling off. That's if Ebay doesn't offer anything better up.

Steve

 

[removed account4]

They're called "stubbie coolers", John. At least that's what they're called here in Australia.

that is good to know ! cause ... they fit perfectly on a 15" teleoptar !

 

[TheFlyingCamera]

Folks here in the US call them "beer coozies" (why I have no idea). I second the nomination for wraps - I have one for every large format lens, even if it has both front and rear caps. I label each wrap with the lens that goes in it so I don't have to worry about confusing them, and it helps to keep the lens caps organized - open the wrap just enough to remove the lens, drop the caps in, close the velcro on it again, and voila!