Lubricating gears on view cameras

Shinnya · Nov 23, 2004

Hi,

I would like to know what sort of lubricant that I should use for gears on view cameras. Also, where I can get them? Any suggestions would be appreciated. Thank you in advance.

Warmly,
tsuyoshi

David A. Goldfarb · Nov 23, 2004

On my Technika I just use a little lith grease. You can get it at a hardware or auto parts store. A small tube or container will last a lifetime.

You can clean out old grease with naphtha.

mikepry · Nov 23, 2004

Ronson Lighter Fluid = Naptha

Loose Gravel · Nov 23, 2004

Sewing machine grease is good. I especially like the teflon grease that the bicycle folks use.

gma · Nov 23, 2004

Silicone grease such as Permatex dielectric tune-up grease lubricant is good. It does not drip and very little is required for gears, threads and other small parts.

Christian Olivet · Nov 23, 2004

This year I went on a photographic trip / workshop in Iceland. I guess I don't have to explain that it gets cold there. My metallic Kodak Master 8x10 got quite sticky at those temperatures. I was wandering if pure silicone or even graphite would be a better option.
I think it has to be a dry lubricant to avoid dirt sticking in to it. Maybe something with teflon?

Flotsam · Nov 23, 2004

I think that if I had a problem with my 4x5, I might try paraffin first. I used to use it on my bicycle chains. Good lubrication, stays where it's put, doesn't pick up dirt, not greasy.

Jorge · Nov 23, 2004

Well, what kind of gears are these? If they are brass all you need to do is clean them very well, brass does not need a lubricant to work properly. In fact it is worse if you do it, since mostly is gathers more dust and makes it worse.

If the camera is made of wood, you run the risk of getting the lubricant between the brass or metal gear and the wood, which can cause wood rot.

I am going to go against the grain here and recommend you do not lubricate, just clean very thoroughly, if necessary with a tooth brush, but leave the lubrication alone.

dr bob · Nov 24, 2004

I go with Jorge. My experience with various lubricants has been variable but mostly bad. To make your wood parts slip (like the older negative carriers) try rubbing a very little bees wax on a spare carrier and slip it in and out a couple of times. Then wipe it down with a soft lintless cloth or a product like Kem-wipe. It will not migrate into unwanted areas. It lasts a long time and is quite stable.

wfwhitaker · Nov 24, 2004

There's a product called Slide-All marketed by Elmer's (as in Elmer's glue...) which consists of microscopic particles of Teflon in an aerosol spray. Once the propellent evaporates, the result is a dry lubricant. Overspray can be a problem, but it wipes up easily as long as it's in an accessible area. I've used it with great success to lubricate Grafmatic holders and occasionally rails on a field camera.

JackRosa · Nov 24, 2004

I also go with Jorge. It depends upon what type of gears we are discussing. If they are brass (or similar) gears, I would recommend graphite - you can purchase graphite powder at any auto parts store or simply take a #2 (or softer pencil - e.g. B) and use the graphite tip of the pencil on the gears. Graphite works wonders on brass gears!

Christian Olivet · Nov 24, 2004

wfwhitaker said:
There's a product called Slide-All marketed by Elmer's (as in Elmer's glue...) which consists of microscopic particles of Teflon in an aerosol spray. Once the propellent evaporates, the result is a dry lubricant. Overspray can be a problem, but it wipes up easily as long as it's in an accessible area. I've used it with great success to lubricate Grafmatic holders and occasionally rails on a field camera.

And where do you get the Slide-All made by Elmers? Funny that you have to buy a lubricant from the manufacturers of glue.

BarrieB · Nov 25, 2004

Monorail or Field Camera ?
Most parts if kept clean are better off with-out any lubricants as the amount of use / movements will not cause much wear, however you can spray some Silicone onto a rag and apply it sparingly to moving parts, often it is the rails that rub together than need some lubrication, not the gears. Grit, sand or dust in /on gears is bad so do not use oil.

wfwhitaker · Nov 25, 2004

Christian Olivet said:
And where do you get the Slide-All made by Elmers?

I get it at the local Ace Hardware. I'm sure it's available at other similar retailers.

Christian Olivet · Nov 25, 2004

wfwhitaker said:
I get it at the local Ace Hardware. I'm sure it's available at other similar retailers.

Cool I'got one Ace hardware close by! Will check for it!

Lubricating gears on view cameras

Shinnya

Advertiser

David A. Goldfarb

Moderator

mikepry

Loose Gravel

gma

Christian Olivet

Flotsam

Jorge

dr bob

wfwhitaker

JackRosa

Christian Olivet

BarrieB

wfwhitaker

Christian Olivet

Lubricating gears on view cameras

Advertiser

Moderator

Privacy & Transparency

Privacy & Transparency