Hints to clean old easel blades....

[hoganlia]

Hi folks... super hot here in my part of the world (38ºC in the shade this afternoon)... not darkroom-friendly at all, so I am developing and working my way through the "I must get around to..." list.

I was given an elderly 40x50cm Meopta easel a while back. A very solid and tempting option which in general is in good shape. The blades however are rather stiff and difficult to adjust. (So far I have been tapping gently with a wooden kitchen tenderizer) I don't think they are rusty but I would like to ease them up if I can without damaging them or using cleaning products which I am later going to regret. They don't have clamps or springs to ease their purchase.... just nice, solid mid-european People's Republic of It's This and Nothing More Are You Complaining? technology.

Any suggestions?

Thanks in advance as always.

Joe

 

[Don_ih]

Clean it with an oily rag to lubricate it slightly? Hard to offer a suggestion without knowing what it looks like.

 

[hoganlia]

Clean it with an oily rag to lubricate it slightly? Hard to offer a suggestion without knowing what it looks like.

how do I upload a photo here?

 

[bdial]

how do I upload a photo here?

click on the little picture icon at top of the reply block, it will let you drag and drop a picture from your computer, or you can copy and paste into the reply.

As for cleaning, for things like easels, that need just slight lubrication, I like paste wax, it has some solvents, so it can loosen old grime, then it leaves a smooth slick surface.

 

[MattKing]

click on the little picture icon at top of the reply block, it will let you drag and drop a picture from your computer, or you can copy and paste into the reply.

The uploader is a bit finicky. If the file is big, re-size it down to a jpeg with 1000 pixels on the long dimension first.

 

[hoganlia]

 

[hoganlia]

click on the little picture icon at top of the reply block, it will let you drag and drop a picture from your computer, or you can copy and paste into the reply.

As for cleaning, for things like easels, that need just slight lubrication, I like paste wax, it has some solvents, so it can loosen old grime, then it leaves a smooth slick surface.

The uploader is a bit finicky. If the file is big, re-size it down to a jpeg with 1000 pixels on the long dimension first.

Thanks to both of you.... the uploader is a lot easier than some of the forums I have been in... Spain's Canonistas is a disaster.

OK... there is cosmetic rust which I would like to clean off if I can but no evident rtust that is causing the bloackage... probably most "dust and grit". The slider in the second photo I think is supposed to elevate a little with upward pressue, not squeezing like many. I presume I will need some sort of oil or lubricant as Don.ih mentioned in his reply but I am not sure which sort... I don't want minimal residues causing problems with paper or anythng

Anyway, the easel itself is extremely solid and the blades sit completely flat (better than the LPL that I am currently using..). I also much prefer the border adjustment mechanism whic is so basic nut effective that I have no isdea why all easels are built this way. The other reason I want to use this is that I would love to try some larger paper... I have a Meopta Opemus 6 enlarger and so far I have used only 5x7 and 8x10 papers....

once again, thanks to all

Joe

 

[Don_ih]

You don't want to coat it in oil or anything. Using a furniture polish after a good cleaning would work - like the paste wax mentioned by @bdial . I've used spray furniture polish on dark slides in film holders - the spray leaves a coating that's quite slippery. You spray it on and wipe it off. I first heard of using that as advice for making the shutter blades in a Packard shutter more frictionless.

 

[Don_ih]

One potential issue with something made like that is the metal can corrode somewhat under the paint, which can make it swell. Pieces that fit nicely when originally painted can end up too tight and no amount of lubrication will fix the situation. In that instance, it might be necessary to take it apart and sand all the surfaces until the pieces fit nicely, then coat in something like furniture polish (helps prevent further corrosion).

 

[Renato Tonelli]

After taking it apart and cleaning it and putting it back together (there goes the day…), lubricate with silicone spray (not too much); it has worked well on my paper cutter.

 

[hoganlia]

You don't want to coat it in oil or anything. Using a furniture polish after a good cleaning would work - like the paste wax mentioned by @bdial . I've used spray furniture polish on dark slides in film holders - the spray leaves a coating that's quite slippery. You spray it on and wipe it off. I first heard of using that as advice for making the shutter blades in a Packard shutter more frictionless.

After taking it apart and cleaning it and putting it back together (there goes the day…), lubricate with silicone spray (not too much); it has worked well on my paper cutter.

I had started to think that taking it apart may be the best option.... thanks for the silicon spray tip as well.

Much obliged!

 

[hoganlia]

click on the little picture icon at top of the reply block, it will let you drag and drop a picture from your computer, or you can copy and paste into the reply.

As for cleaning, for things like easels, that need just slight lubrication, I like paste wax, it has some solvents, so it can loosen old grime, then it leaves a smooth slick surface.

I don't know what "paste wax" is..... hahaha.... I haven't lived in an English speaking country (or environment) for 43 years.... English is now my second language... or maybe even third. I'll see what I can find.

Aha, just checked amazon... furniture wax Thanks

 

[Don_ih]

Spray furniture polish also counts as a silicone spray, by the way. But lemon-scented

 

[Patrick Robert James]

The blades obviously need friction to stay in place. Figure out what is causing too much friction and ameliorate it. You might be able to slide the blades off the end and clean them completely. The Leitz easel is similar to what you have, though the Leitz easel has locks.

I'd rather have too much friction than not enough though so be careful what you lubricate it with.

 

[BMbikerider]

Clean it with an oily rag to lubricate it slightly? Hard to offer a suggestion without knowing what it looks like.

Oh dear! Don't ever allow oil of any description or quantity get anywhere near photographic darkroom equipment. Obviously you will be working in the dark and oil has a habit of spreading - even a smear will spread! I would suggest checking the blades to see iuf there are rough spots which may be corrosion and lightly dressing this down with a 1000 grit production paper. (Used in car body repair shops) Then when it is smooth with no rough areas cover the blades all over with a good Bees-wax polish and buff the aread and you will find that it makes a world of change to the movement.

I make no apology for repeating what I said at the start DO NOT USE OIL!

 

[hoganlia]

Oh dear! Don't ever allow oil of any description or quantity get anywhere near photographic darkroom equipment. Obviously you will be working in the dark and oil has a habit of spreading - even a smear will spread! I would suggest checking the blades to see iuf there are rough spots which may be corrosion and lightly dressing this down with a 1000 grit production paper. (Used in car body repair shops) Then when it is smooth with no rough areas cover the blades all over with a good Bees-wax polish and buff the aread and you will find that it makes a world of change to the movement.

I make no apology for repeating what I said at the start DO NOT USE OIL!

I(nteresting idea re the grit paper... I was in an iron.mongers the other day and on the way home I thought about asking their advice on just that.

 

[MattKing]

Gentlemen.
We already have your advice - care with any type of oil is necessary, and some things may surprise you with their oil content.
If you intend to continue your argument, please don't use the public forums.

 

[Don_ih]

Okay, Dad

 

[mshchem]

Automobiles are made of painted metal, maybe try an inexpensive auto polish.

 

[hoganlia]

Thanks everyone for your support and advice. I've decided to take the easel to a metal shop to get expert advice before I sally ahead on my own and possible destroy things. A number of things people mentioned here rerally were food for thought. What a great forum this is.

Thanks to all

Muchísimas de las gracias

 

[glbeas]

One thing I have used on sticky sliding machine parts is to dab a scotchbrite pad with carnauba floor wax and buff the metal with it. Results are a nicely sliding part with a fine coat of wax to lubricate it.