Fomatone MG Classic edge frilling

[AnselMortensen]

I printed on some of this paper today and noticed some edge frilling... loss of emulsion along the edges.

Anybody have a recommendation on how to avoid this?
Thanks!

 

[mshchem]

No one will want to hear this. Hardener in the fixer. Same for other Foma fiber base paper. No big deal just use hypo clear. Followed by washing in 20 C water for 20 minutes (minimum)

I use Kodak rapid fix film strength with Hardener for a couple minutes. If you want to check for adequate fixing check with selenium toner.

No hard science to back this up, but Foma paper seems to have softer gelatin, which is (possibly) damaged slightly when the paper is finished at the factory.

MHOFWIW YMMV

 

[Paul Howell]

I use Kodak or clone regular fixer with a hardener for all my papers, rc and fb.

 

[DREW WILEY]

I didn't get frilling, but fine indentations (not exactly scratches) in the emulsion from ordinary handling. Seems more fragile than other papers.

 

[mshchem]

I use Kodak or clone regular fixer with a hardener for all my papers, rc and fb.

Works great!

 

[Milpool]

Could this be due to poor storage/distribution conditions before it makes its way to the customer?

With respect to processing Foma doesn’t indicate anything special for this paper. If there was no user error this isn’t acceptable.

I’m hoping to be able to switch from Ilford papers to Foma but this sort of problem or other defects are a no go.

 

[mshchem]

Could this be due to poor storage/distribution conditions before it makes its way to the customer?

With respect to processing Foma doesn’t indicate anything special for this paper. If there was no user error this isn’t acceptable.

I’m hoping to be able to switch from Ilford papers to Foma but this sort of problem or other defects are a no go.

It's not a big problem at all. No reason to switch from Ilford to Foma or vice-versa. Use both.

 

[mshchem]

People are missing tremendous products by avoiding Foma. Just sayin'

 

[koraks]

@AnselMortensen you're not the first (and probably not the last) to run into flaking problems along the edges of Foma papers. I've personally never seen it happen. However, this recent thread on Fomabrom (a different paper of course, but same mfgr) at least shows you're not alone: https://www.photrio.com/forum/threads/fomabrom-variant-iii-emulsion-flaking.213430/ Sadly, I don't think it ever resulted in clear causes or solutions of the problem.

The problem has been discussed several times over the years IIRC. It's very rare for people to post examples, sadly. Perhaps you could be the change....the linked thread has one illustration which I think is the only one I ever saw. It would be useful to be able to see what it looks like on your end so that we at least can determine whether it's the same problem.

 

[Milpool]

It's not a big problem at all. No reason to switch from Ilford to Foma or vice-versa. Use both.

If it’s a batch issue or something then I agree but if it happens fairly regularly then I would call that a big problem. I’d like to move away from Ilford but not if it’s a crapshoot regarding potential problems and not if I have to switch to ancient hardening fixation.

 

[retina_restoration]

People are missing tremendous products by avoiding Foma. Just sayin'

I agree. Fomatone Classic is a beautiful paper. And I’ve never seen drilling or any other kind of emulsion damage on this paper, and I use TF-5 fixer, no hardener.

 

[AnselMortensen]

Thank you for all the comments.
I love the olive tones I'm getting from the paper, I'm hoping I can find a workaround to eliminate the issue.
I am using it for contact printing 8x10 negs, and the black border makes the frilling pretty obvious.
I'll post a pic in a couple days.

 

[retina_restoration]

Thank you for all the comments.
I love the olive tones I'm getting from the paper, I'm hoping I can find a workaround to eliminate the issue.
I am using it for contact printing 8x10 negs, and the black border makes the frilling pretty obvious.
I'll post a pic in a couple days.

I contact print 8x10 negs on Fomatone as well, but I use 11X14 paper for this, so there's always lots of room to cut the paper down if I need to.

 

[AnselMortensen]

I contact print 8x10 negs on Fomatone as well, but I use 11X14 paper for this, so there's always lots of room to cut the paper down if I need to.

Thank you, that would be a viable workaround for me.
I can use the 8x10 paper for contacting my 5x7 negs.

 

[Lachlan Young]

If it’s a batch issue or something then I agree but if it happens fairly regularly then I would call that a big problem. I’d like to move away from Ilford but not if it’s a crapshoot regarding potential problems and not if I have to switch to ancient hardening fixation.

It demands slightly more careful handling, and chucking a bunch of sheets into a tray and slamming them into each other isn't a great idea, but the only times I've had real issues were with a slightly less than fully sharp guillotine leaving a bit for a squeegee to catch on on some cut down pieces (and even then it was not a big deal) - and that sulphide toners can soften it a bit if used at stronger dilutions and longer times. I'd say Foma's papers are hardened to about 70s/80s levels, rather than with vinyl ethers. Major thing to keep an eye on is the longer fixing times needed.

 

[Milpool]

Thanks, Lachlan. I have some Foma papers to try so I guess I will find out. I’ve always been extremely careful handling / processing / washing paper anyway so maybe it will be ok.

It demands slightly more careful handling, and chucking a bunch of sheets into a tray and slamming them into each other isn't a great idea, but the only times I've had real issues were with a slightly less than fully sharp guillotine leaving a bit for a squeegee to catch on on some cut down pieces (and even then it was not a big deal) - and that sulphide toners can soften it a bit if used at stronger dilutions and longer times. I'd say Foma's papers are hardened to about 70s/80s levels, rather than with vinyl ethers. Major thing to keep an eye on is the longer fixing times needed.

 

[DREW WILEY]

The issue is a lot more evident for me when handling test strips, which might get cut and potentially bent and so forth less carefully than my actual full print pieces. I've certainly had some edge frilling in those cases.

 

[logan2z]

I'll chime in here because @koraks referenced the thread I started on a similar subject several months ago.

Freestyle did replace the first package I bought and I haven't had an issue since. In fact some other sheets from the first box haven't exhibited the issue either. So it seems like it was an isolated case. The paper is very nice and I'll continue to use it, but I'll exercise additional caution while handling it wet just in case.

 

[joho]

Just my 2 cents if for archive work or prints for sell a border of say five cm. all-around is useful.
prints can be handled W/O touching the print surface --ect-ect-