Epson 3800 and Pizza Wheels

OP
OP

Patrick Kolb

Member
Joined
May 17, 2004
Messages
54
Location
Portland, Or
Format
Large Format
I just wanted to follow up on this thread. I have installed QTR and have it adjusted for my workflow and although there are still some pizza wheels on the film, they do not show in the print. Thank you everyone that has helped with this. Also, it is nice to know that one can always front load the Pictorico from the front, if you have the room.
 

sanking

Member
Joined
Mar 26, 2003
Messages
5,437
Location
Greenville,
Format
Large Format
Sidney et al

I tried the front manual feed slot on the Epson 3800 and it worked nicely. I simply taped the Pictorico OHP to a sheet of 7 mil mylar with litho tape. It worked perfectly for me. The front manual load definitely eliminates any problem of pizza wheel marks.

Much nicer mechanism than on the HP b9180.

Thanks to Sidney for posting about this.

Sandy






 

Colin Graham

Member
Joined
Sep 5, 2004
Messages
1,264
Format
Plastic Cameras
I wanted to mention that my pizza wheel problem vanished as soon as I started using the sheet feed support at proper extension and PK inks instead of MK inks. Not sure which had more impact, started doing both at the same time. I'm embarrassed to admit how long it took me to realize that the telescoping sheet feed support was even there.
 

sanking

Member
Joined
Mar 26, 2003
Messages
5,437
Location
Greenville,
Format
Large Format
Colin,

I will just throw in that I have not had any pizza wheel marks with the 3800 using the MK inks and the back sheet feeder. I hope to switch over to the PK inks to see if I can get less grain with carbon, but unfortunatley don't have much time for this right now as I am working hard to finish an article on the B&S carbon symposium for View Camera and need to get it done before I leave for China in mid-September.

Sandy King




 

Colin Graham

Member
Joined
Sep 5, 2004
Messages
1,264
Format
Plastic Cameras
You sure have a full plate! I'm very much looking forward to seeing the article. And I'm quite envious of your trip to China. Hope you have a great visit.
 

Philippe Berger

Member
Joined
Jan 10, 2005
Messages
106
Location
Belgium
Format
Multi Format
Contact Sidney

Bonjour Sidney,

J'aimerai acheter une impriimante epson r3000 pour imprimer des négatifs sur transparent Pictorico.
Impossible de les introduire par l'arrière à cause des Pizza Wheels.
Je 'arrive pas à les introduire par l'avant.

Je crois que vous avez une technique qui fonctionne.

J'aimerais vous téléphoner pour avoir votre expérience et savoir ce que vous en pensez.

Si vous êtes d'accord bien sûr

Voici mes coordonnées
mineurdecharbon@skynet.be et tél 00 32 4 369 34 96

Si vous êtes d'accord envoyer moi vos coordonnées téléphoniques et je vous téléphone à l'heure que vous souhaitez, j'habite en Belgique et parle le français

Merci d'avanvce de votre aide

Philippe
 

Zero_Equals_Infinity

Member
Joined
Dec 18, 2010
Messages
70
Format
Multi Format
Use the front end loader with the included cardboard as a backing and all will be will. No pizza wheels result when using the front end loader. (Note you do not need to tape Pictorico to the backing just align it well and gently insert in through the front-end loader.) Be aware that the QTR profile you are using will change by using the front end loader, so start by using the front-end loader rather that the rear. I also find that I have a high success rate of first time alignment, whereas using the rear it has often required multiple attempts to get the printer to accept the film as properly aligned.
 

Philippe Berger

Member
Joined
Jan 10, 2005
Messages
106
Location
Belgium
Format
Multi Format
I thought I should paste the transparent Pictorico on a sheet of thick paper with glue to bring all the front of the Epson R3000?

You intoduisez transparency from the front only. Y t is a well-specified

thank you
 

chuck94022

Member
Joined
Jan 11, 2005
Messages
869
Location
Los Altos, C
Format
Multi Format
sanking said:
... I leave for China in mid-September.

Sandy King
Click to expand...

Sandy,

Where will you be in China. I'm in Beijing and would love to meet you. Will you be doing a workshop, or touring, or ???
 
Last edited by a moderator:
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…