Converting a Brownie #3 to Wet/Dry plate

[sdivot]

I'm sure this has probably been covered before, but I can't find it.
Can someone tell me how, or direct me somewhere that tells how to modify a Brownie Box #3 camera to wet/dry plate? I suspect it's not too difficult. Yes?
Thanks,
Steve
www.scdowellphoto.com

 

[TheFlyingCamera]

No modifications per se are necessary for a box camera. Just cut your glass plates to the size of the film gate and voila! you have a wet plate camera.

 

[Ian Grant]

No modifications per se are necessary for a box camera. Just cut your glass plates to the size of the film gate and voila! you have a wet plate camera.

Have you tried putting a wet-plate into an unmodified Box Brownie, they are designed for roll-film

Yes it might work but in a very impractical way as the camera has to be taken apart to change each plate.

You'd need to make a whole new section to hold a plate holder light-tight, there are far better cameras to start from.

Ian

 

[Allen Friday]

I modified a Brownie last year for wet plate. THe Flying Camera is right in that you just cut the plate to the size of the opening, put the wet plate in the camera in the darkroom and then run outside to do your exposure. But, one change I did make was to cover the metal on the back of the camera with electrical tape so that the wet plate emulsion will not touch metal and react with the metal. Wipe off the tape completely between exposures so you don't contaminate the new plate.

The Brownie is a great little camera for learning wet plate. All the basics are covered. The only problem, which isn't very big given the portability of the camera, is you have to carry the entire camera in and out of the darkroom.

 

[RobertP]

Put a coat of varnish all over the inside. This will protect it from the silver nitrate. Box brownies make great wet plate starter cameras. I think the #3 is a perfect fit for 1/4 plate.

 

[sdivot]

Thanks guys.
What exactly are the dimensions of quarter plate?
Steve
www.scdowellphoto.com

 

[TheFlyingCamera]

Have you tried putting a wet-plate into an unmodified Box Brownie, they are designed for roll-film

Yes it might work but in a very impractical way as the camera has to be taken apart to change each plate.

You'd need to make a whole new section to hold a plate holder light-tight, there are far better cameras to start from.

Ian

Ian- I have shot wet plate in a box brownie before. Loading/unloading the camera is no more inconvenient than loading/unloading the holder, because the cameras are rather small relatively speaking. I just make sure to wipe down the surfaces that contact the plate between uses, and all is well.

 

[bill schwab]

Yes it might work but in a very impractical way as the camera has to be taken apart to change each plate.

As Scott said, Brownies actually make great little wet plate cameras.

What exactly are the dimensions of quarter plate?

3.25 x 4.25 inches. Have fun!

 

[RobertP]

Another thing that has not yet been mentioned is that you are probably limited to shooting only tins/trophy aluminum. Glass is probably to thick and won't allow you to close the camera. Maybe others can confirm this.

 

[Ian Grant]

I have to concede Scott & Bill are right, personally I wouldn't potentially ruin a good Box Brownie for what I'd see as quite an inconvenient camera, however I think you'd be able to get the glass inside OK and the camera closed.

However they have convinced me that it's possible, which is what the OP was asking, with no modifications to the camera.

Ian

 

[TheFlyingCamera]

RobertP-

I have shot black glass ambros in a #2 Box Brownie (approx 1/4 plate size - 3 1/4 x 4 1/4 or thereabouts). They fit just fine. Brownies were far from precision equipment, and they had plenty of play. In fact, the #2 that I use has a pair of big springs to keep the film flat, which work great for keeping the glass in place.

 

[RobertP]

Thanks Scott, I stand corrected. Robert

 

[sdivot]

Thanks everybody. I bought the Brownie, but have not received it yet. I'll let you know how it goes.
Steve
www.scdowellphoto.com

 

[eddie gunks]

I have to concede Scott & Bill are right, personally I wouldn't potentially ruin a good Box Brownie for what I'd see as quite an inconvenient camera, however I think you'd be able to get the glass inside OK and the camera closed.

However they have convinced me that it's possible, which is what the OP was asking, with no modifications to the camera.

Ian

i just got john coffers video. in the video demonstrates exactly how to convert and shoot with the 3A..........

 

[smieglitz]

I just epoxied some aluminum corners onto the back to keep the plate at the film plane, then spray painted it matte black. You should probably cover the ruby window just in case.

Tins will fit. Glass won't.

 

[RobertP]

Joe, This is like the Coffer conversion. I thought he did mention that glass won't fit but I wasn't sure. Thanks Robert