Advice needed... Basement darkroom

Rick A

Subscriber
Joined
Mar 31, 2009
Messages
9,964
Location
Laurel Highlands
Format
8x10 Format
There may be a reason Kodak used yellow paint and tiles in all their DR's.
 

cowanw

Member
Joined
Aug 29, 2006
Messages
2,243
Location
Hamilton, On
Format
Large Format
I think the theory is mainly related to reflected light, the best example being the cracks in the enlarger around the film holder. Any Paper exposing light would in theory be absorbed by the walls. Maybe this would be better than black around the enlarger. I would try it if I hadn't painted mine black like everybody recommended, 30 years ago.
The colour might be a representation of wavelength that the paper is insensitive to. Like a kodak #1 or OC
I have never been in a bordello, so I don't know what they look like.
When I look at my bamboo tongs I can't tell the yellow from the red under safelight.
 

AlbertZeroK

Member
Joined
Jan 16, 2011
Messages
539
Location
Central Virg
Format
Medium Format
I've actually got a new-to-me 23C II enlarger in my van ready to come to it's new home in my basement darkroom. I've still goto to light proof it but I've been developing film using a dark box (which I love) and hanging it with clips on the 6 gauge bare copper ground line in the ceiling.

I plan on hanging canvas around my enlarger to capture light.

Also, I stole one of my wife's old work out matts and it has been AmAZING on my feet! If it wasn't for that, I'd be all over horse matts!

I didn't spluge for a darkroom sink, instead got a cheap utility sink from Lowes. Got shelves from the Habitat for Humanity ReStore. As for counter top, I've been using a 3/4 in thick wood counter top in my kitchen for years - just treat it regularly with mineral oil, same as i use on my Boss Block (the kitchen is my other favorite room in the house.) I used the same wood in the basement.

The only thing I need to do now is get a print washer and run some lines for drying. Bur for a print dryer, I'm going to use a funnel into a piece of PVC pipe attached to a piece of Plexiglass with holes in it. And I'll probably build a drying box for my negatives.

I'm also installing a computer and my scanner in my dark room, should be fun killing all those lights! Of course, I should just use my old laptop for that...

But I would definatly get something to go under your feet!
 

David Brown

Member
Joined
Feb 16, 2004
Messages
4,056
Location
Earth
Format
Multi Format
J Rollinger said:
Paint... Does color matter? Does finish matter? Will a gloss paint have any affect while printing?
Click to expand...

APUG seems to have semi-annual long threads about this. You've just missed the most recent one.

I'd go with a beige or puce, and aubergene behind the enlargers.
 

RalphLambrecht

Subscriber
Joined
Sep 19, 2003
Messages
14,683
Location
K,Germany
Format
Medium Format
Mats_A said:
Please do tell.

r

Mats
Click to expand...

Turn on your safelights, take the CD, look at the back of it until you see a reflection of the safelight and bend it slightly until it breaks the light and you can see the spectrum. A 'safe' safelight will not have any blue and very little green content.

Practice first in white light to appreciate the difference.
 

RalphLambrecht

Subscriber
Joined
Sep 19, 2003
Messages
14,683
Location
K,Germany
Format
Medium Format
Thanks Isaac Newton. In 1670, he demonstrated that a prism could decompose white light into a spectrum of colors. I just replaced the prism with a CD and tested how 'white' the safelight is. Missing the blue and green components of the spectrum will indicate relatively 'safe' conditions.
 
Last edited by a moderator:

StephanA

Member
Joined
Mar 12, 2011
Messages
8
Location
Boca Raton,
Format
35mm RF
Having worked in both commercial color and b&w darkrooms and built a couple of my own, I, like the rest have a few recommendations. For the floor, use a waterproof paint in a neutral color (I used gray), and get the restaurant kitchen pads to step on in black. Do not use the red ones. They are easy to pick up and clean, plus they last darned near forever! On the walls, use a very neutral semigloss white paint. Darkrooms are called that for a reason and you want your safelights to give you enough light to work with. I found that having the walls on the enlarger side and the wet side covered with pegboard very helpful. You might not even need the shelving with that up. My last suggestion is to wall mount your enlarger(s) and build your enlarging table so you can adjust the height of the paper surface similar to the shelf adjusters in an oven. These things have worked great for me.
 
OP
OP

J Rollinger

Member
Joined
Jan 31, 2009
Messages
468
Location
Chicago, IL
Format
Multi Format
Thanks for all the adivce everyone!! I finished the platforms for the enlargers, all electrical and painting. I fellow Apuger earlier in this thread mentioned wired shelves from Home Depot so i went there.. They were perfect for what i needed and came in 6ft lengths to match sink. If they rust i will just snap it off and put a new one on. The floor is a lost cause... I tried to even it out today but its just bad so I'm going with painting the floor gray and using black mats. I'm getting very excited to complete it so i can print again!!!! I will scrub the floor good in the next 2 days so it dries out for painting this weekend. After the floor all i have to do is put the sink in and find a base cabinet at Home Depot then I'm done! Below is a photo of the platform and enlarger. I was surprised that the enlarger would not fit but luckily there is only 8 screws to remove the chassis from the baseboard, not it fits.

Thanks again for the help, I appreciate it!

Jim
 

Attachments

  • 005.JPG
    34.2 KB · Views: 119
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…