Yellow stain

Pieter12

Member
Joined
Aug 20, 2017
Messages
7,640
Location
Magrathean's computer
Format
Super8
I recently made a batch (maybe 10) of 11x14 identical prints. Same times, same chemicals, all fresh, all processed in a Nova vertical slot processor. For some reason one of them has a light yellow/brown tint or overall stain. It was towards the end of the session, but I'm not sure if it was the last print or not. What caused this? Exhausted fixer?

 

koraks

Moderator
Moderator
Joined
Nov 29, 2018
Messages
23,441
Location
Europe
Format
Multi Format
Pieter12 said:
Exhausted fixer?
Click to expand...

Possibly. Could also be dichroic fog due to excessive developer carry-over. Or light fogging which for some reason turned up on just this sheet (phone screen coming for on for a second etc.)
It's not evenly distributed across the sheet, is it? What's the pattern?
 
OP
OP

Pieter12

Member
Joined
Aug 20, 2017
Messages
7,640
Location
Magrathean's computer
Format
Super8
it is even over the entire sheet. I might need to increase the stop bath time, right now it is 20 seconds, plus 10 seconds draining over the slot.
 

koraks

Moderator
Moderator
Joined
Nov 29, 2018
Messages
23,441
Location
Europe
Format
Multi Format
To be honest, I never ran into problems with similarly brief stop, even if it was getting somewhat dodgy towards the end of a session. It's worth a shot, but I doubt it's the main issue.
You sure the fixer was within capacity throughout that session?
 

Sirius Glass

Subscriber
Joined
Jan 18, 2007
Messages
50,411
Location
Southern California
Format
Multi Format
Pieter12 said:
it is even over the entire sheet. I might need to increase the stop bath time, right now it is 20 seconds, plus 10 seconds draining over the slot.
Click to expand...

The directions usually state 30 seconds for stop bath, but the timing is not critical so I just use one minute which is long enough to get the job done yet short enough to not cause any other problems.
 
OP
OP

Pieter12

Member
Joined
Aug 20, 2017
Messages
7,640
Location
Magrathean's computer
Format
Super8
koraks said:
To be honest, I never ran into problems with similarly brief stop, even if it was getting somewhat dodgy towards the end of a session. It's worth a shot, but I doubt it's the main issue.
You sure the fixer was within capacity throughout that session?
Click to expand...
Fixer data sheet says I should get 40 8x10's (3200 sq. in., about 20 11x14s) per liter for archival fixing. The Nova holds about 2 liters in each slot, so I think iI should have been well within capacity.
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
53,252
Location
Delta, BC Canada
Format
Medium Format
Any chance that with that particular sheet the stop bath was impeded from reaching the emulsion?
 

Peter78

Member
Joined
Nov 27, 2014
Messages
4
Format
Medium Format
Hello!

I have just run into the same issue. Did you figure out what was causing the problem?

My guess is that maybe the 4-5 years old "expired" papers(Fomatone MG) I used might have some more intensive exhausting effect on developer than normally the fresh papers have.
 

gone

Member
Joined
Jun 14, 2009
Messages
5,504
Location
gone
Format
Medium Format
I had that happen once. All my prints were neutral except for the last one, and it was quite warm. Turns out that this is what happens w/ Dektol when it's almost exhausted. So if the op used Dektol, that might be the issue.
 

pentaxuser

Member
Joined
May 9, 2005
Messages
20,017
Location
Daventry, No
Format
35mm
Call it a faulty instinct on my part as it may well be just that, but somehow I cannot see the stop bath dilution being the cause

pentaxuser
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
53,252
Location
Delta, BC Canada
Format
Medium Format
Exhausted stop bath can lead to developer contamination of fixer which can lead to stained prints.
 

Peter78

Member
Joined
Nov 27, 2014
Messages
4
Format
Medium Format
I can confirm too that the weak(not working?) stop bath caused the yellow stain on my prints too!
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…