What is this thing?

JBrunner

Moderator
Moderator
Joined
Dec 14, 2005
Messages
7,429
Location
PNdub
Format
Medium Format

Moopheus

Member
Joined
Dec 31, 2006
Messages
1,219
Location
Cambridge MA
Format
Medium Format
It's a repro camera for prepress work--making film (to make plates for printing) from camera-ready copy.
 
OP
OP

JBrunner

Moderator
Moderator
Joined
Dec 14, 2005
Messages
7,429
Location
PNdub
Format
Medium Format
Moopheus said:
It's a repro camera for prepress work--making film (to make plates for printing) from camera-ready copy.
Click to expand...

I wonder how hard it would be to make it work backwards? Might have a decent lens.
 

Mick Fagan

Subscriber
Joined
Sep 13, 2005
Messages
4,421
Location
Melbourne Au
Format
Multi Format
Jason, for $100 you will (or should) have a beautiful vacuum back, about the size of an A3 or oversized A3 possibility.

There is then the two lenses, one will probably be a 150 G f9 Rodenstock the other a 240 wide angle which will cover 8x10 like you wouldn't believe and is probably designed to cover a 12x16" or 30x40cm sheet of film. You will of course have to figure out how to put shutters in them, but I mean to say!

Why don't you just bop on down there?

Have you left yet?

Mick.
 

Frank Szabo

Member
Joined
Sep 2, 2007
Messages
311
Location
Broken Arrow
Format
8x10 Format
deleted - gave some bad info.
 

mpirie

Member
Joined
Sep 19, 2005
Messages
598
Location
Highlands of Scotland
Format
4x5 Format
Yep, we used to use the Repromaster for making lith negs.

IIRC the timer on the right side would switch the lamp on and off as per your exposure and it was used under normal safelight conditions in the darkroom.

The hand-wheels on the right and left were used to alter the magnification by raising and lowering the light table.

I doubt the timer and lamp combination would be accurate or refined enough to use as a 10x8 enlarger.
 

paul ewins

Member
Joined
Jan 5, 2006
Messages
446
Location
Melbourne, A
Format
4x5 Format
There's a good chance the lenses will be Staeble/Eskofot Ultragons that can't be remounted easily into shutters. If they are Schneiders then you will have got your $100 back straight off. The only thing to remember is that these items are usually quite heavy and bulky. I bought one a couple of years ago for $10 and needed a hire trailer to get it home. It was loaded with a forklift and I had to disassemble it on the trailer as it was too heavy to move. I got a few good bits and a whole lot more went in the skip.
 

PHOTOTONE

Member
Joined
Oct 30, 2006
Messages
2,412
Location
Van Buren, A
Format
Large Format
A graphic-arts camera like this is intended to make litho-negs of reflective art. Not transparent art. Therefore you could not "easily" make it into an enlarger without constructing a light source that would shine thru a negative. Still, there may be enough "salvage" on it to make it worth $100 if you can get it locally. The 2 lenses, and the mechanism for the vacuum back (if it has a vacuum back) should be worth $100.
 

raucousimages

Member
Joined
May 12, 2003
Messages
824
Location
Salt Lake
Format
Large Format
Jason.
Call me if you want to go take a look,we can take my truck. I could use the drive.
John
 

lonepeak

Member
Joined
Jun 9, 2007
Messages
30
Location
Utah
Format
4x5 Format
Jason, I saw one in a movie recently and they were using it to make offset printing plates. At least it looked a lot like it??? Barry
 

rcoda

Member
Joined
Dec 19, 2006
Messages
197
Location
Scottsdale,
Format
Large Format
It's what we used to call a "stat" camera used for exposing plates and litho negatives mainly used for print, before the digital era. You could probably modify it to enlarge LF negs.

They are beasts, though. My dad had a printing shop in Passaic, NJ when I was a young kid. They got a new stat camera and had it installed in the basement, where the darkroom was. They had to build a room for it. I would say at least 20x20 ft.
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…