Using hydroponic fan in darkroom

Col9

Member
Joined
Sep 6, 2015
Messages
4
Location
mars
Format
Medium Format
Just joined so this if first post. I am building a new darkroom and want decent ventilation this time. Has anybody used a hydroponic duct fan to blow filtered air into the dark room? I thought of taking air from the house and dusting the exhaust through a vent to the outside. Any suggestions comment would be appreciated.
 

waileong

Member
Joined
Apr 1, 2005
Messages
102
Format
35mm RF
Normal airconditioning works ok. If you want to use any kind of ventilation, remember that light travels only in straight lines, unless there's reflections.
 

gone

Member
Joined
Jun 14, 2009
Messages
5,505
Location
gone
Format
Medium Format
Assuming your room is relatively large and you don't spend all day in there, as wailwong said, you should be fine. It's the fixer that is not fun to breathe, so consider an odorless fixer for the printing. However, from the sound of your post, maybe you had a darkroom once before and the fumes were an issue? If that's the case, then better ventilation would be in order. W/o knowing the particulars, I can't recommend much, and have no experience w/ the filtering that you mentioned. Sorry. Maybe someone else here can give better info.
 

GregW

Member
Joined
Dec 10, 2012
Messages
319
Location
East Coast
Format
Multi Format
For such a small room I would think a simple bathroom vent fan would do the trick, should change the air every 3 minutes or so. Cost should be about a third of the hydroponic? (30 bucks here) Though the ducting etc included with the H fan would be extra. Also would take up less space. You could even have two, one blowing in one blowing out. It would still cost less.
 

ic-racer

Member
Joined
Feb 25, 2007
Messages
16,499
Location
USA
Format
Multi Format
Not sure what a 'hydroponic' fan is , but there are hundreds of posts on darkroom ventilation on this forum.
 

mike c

Subscriber
Joined
Jan 5, 2009
Messages
2,863
Location
Los Angeles
Format
Multi Format
Bath room fans are not that great, I've got one and are not that happy with it. I have read about guys using those inline type of fans with good results , do not know if they were hydroponic .
 

Wayne

Member
Joined
Jul 8, 2005
Messages
3,583
Location
USA
Format
Large Format
I use surplus muffin fans much like these (except ac). They are small, light, cheap, quiet and they rock, and its easy to build a light-tight window insert to mount them in. Waaaaay better than bathroom fan IMO. Two of these work great in my large wet darkroom.

I'm not sure why you would need to filter anything. You want the air vented out, not in. Likewise I'm not sure how well an air conditioner would work. Seems like they would just stir things up. Maybe I'm missing something?

http://www.surpluscenter.com/Electrical/Blowers-Fans/DC-Fans/102-CFM-12-VDC-ROTRON-4-75-MUFFIN-FAN-16-1380.axd
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
52,137
Location
Delta, BC Canada
Format
Medium Format
I prefer to use fans to exhaust the air from the darkroom.

This allows you to place the air intake (for the exhaust) near the trays, in order to draw the air away from them. Flexible dryer exhaust tubing works well for this. So does plastic drain piping.

You can put filters in the (passive) air intake openings.
 

M Carter

Member
Joined
Jan 23, 2013
Messages
2,147
Location
Dallas, TX
Format
Medium Format
I upgraded my bathroom fans with the basic builder-store models and they really move some air and are quiet. I think in some cases the issue may be getting the intake closer to your trays, say by dropping some rigid vent down from the intake.

I had the roof vent installed for my darkroom but haven't gotten the fan in yet (2nd story, Texas attic = hot as hell right now). I do a lot of lith printing with hot trays and you can really get the air pretty thick that way (though I associate the smell with magic and wonder and unicorns-peeing-scotch level happiness, since lith is kind of magical). But ever try heated, strong, selenium toning? I'm not doing that again until I have a fan and maybe a pop-on intake tube to go right above the tray - that's a sinus-burner.

By the way, if anyone has a unicorn that pees scotch, let me know?
 

bsdunek

Member
Joined
Jul 27, 2006
Messages
1,611
Location
Michigan
Format
Multi Format
Not exactly the same thing, but I installed an fume hood in my Wife's glass studio using a hydroponic fan. Really works great. The one I got uses six inch stove pipe for duct, so it's easy to fabricate the ducting. It is a little noisy but not bad. It does a great job pulling the fumes from hot glass out. I think the one I put in is a 900 cfm rated model - for a darkroom, you might get buy with less - say 500 cfm.
 
OP
OP

Col9

Member
Joined
Sep 6, 2015
Messages
4
Location
mars
Format
Medium Format
Thanks for the comments. I will try a hydro ventilation fan with a motor speed controller to vary the amount of air coming through. The idea is to take filtered, warmed air into the darkroom from the house, blow it across the sink and exhaust the other side. The alleged advantage is that when the door is opened dust is not sucked in. If it does not work I can reverse the fan. Taking air from the house will mean it is warmed during winter, pretty much essential here as the village is cold, expecting near 0C tonight.

I know some will think this is overkill but I well remember days spent printing in a small stuffy darkroom without ventilation; the headache and crap feeling the next day. Also, I plan on using some alternative printing processes which makes good ventilation even more essential. I'll post again when it's all installed.
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
52,137
Location
Delta, BC Canada
Format
Medium Format

Add a small exhaust fan that takes in air from near the trays and vents it outside and you will be golden!
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…