Stamping the back of a print. Stamp sources?

[wildbill]

I'm interested in a custom rubber (or whatever) stamp for the back* of my mounted/matted prints as my handwriting is really bad and usually ends up crooked. What type of ink/pad should I get and where (online?) should I get it?
*on the back of the matt board

I'm thinking about 3"x4" size with:
Vinny Walsh Photography

Title:
Print size:
Print #:
Print Type:
Image Date:
Print Date:
my website

thanks
vinny

 

[jovo]

I've not used a stamp primarily because of the possibility of it not registering completely, or smudging etc. Instead, I've used Avery inkjet labels (they come in a large variety of sizes) with their software for setting up what you want to print on them. I print up a number of sheets in advance, and then fill them out and apply them as the prints are finished. The only handwriting is my signature, and the title of the print.

 

[Jim Noel]

Several years ago I also gave up a stamp in favor of Avery labels. I keep generic ones printed and for special prints I make special labels.

 

[blaze-on]

http://www.zippystamp.com/

they'll make anything you want Vinny..and I set up an account there a few years ago if that's needed.
I found it easier to call them as the website is...blah

 

[Ken Nadvornick]

http://www.zippystamp.com/

...the website is...blah

I tried to take a look at their product line, but apparently they won't let you look at anything they're selling until you preregister with all of your personal information. No thanks.

Did I miss the secret decoder ring backdoor entrance, or something??

Ken

 

[wildbill]

John, good point about the smudging or registering, I've dealt with that for my address stamps.
I have some Avery labels but like any other adhesive sticker, I'm sure they'll turn yellow and/or deteriorate over time. Correct me if I'm wrong. I think ink is pretty permanent.
Matt, I'll look into zippystamp.

 

[blaze-on]

They deal with a lot of retailers, hence the account set-up. Standard practice
They have self-inking stamps, which is best for this application and ink that has a permanence suited for this as well.
Talk to them Vinny

 

[Tori8x10]

I've been looking for the same thing, but I think I want to stick with (no pun intended - really!) the labels. Here are two sources I'm looking at:
Dead Link Removed and
http://www.archivalsuppliers.com/prodinfo.asp?number=387-LASER&variation=387-5352

I think I will go with the first one as they are a little less expensive. Then it is just a matter of setting up your own template, or in my case, having someone who knows what they're doing set a template up for me.

 

[Ken Nadvornick]

They deal with a lot of retailers, hence the account set-up. Standard practice.

Fair enough, I suppose.

Like the OP I have also been looking for some way to attach information to the back of the mount board. While ink stamps do seem the way to go, smudging also seems like an inevitability now and then. Especially in my case...

What about (laser) printing onto an appropriate paper, then simply dry mounting (if that's one's mounting choice to begin with) onto the back of the mount? This could be done as a single sandwich in a single pass through the press. If it's permanent for the print - some might say too permanent - it should be likewise for the information sheet. However, I'm not knowledgable regarding the keeping properties and longevity of fused toners.

Ken

 

[wogster]

Fair enough, I suppose.

Like the OP I have also been looking for some way to attach information to the back of the mount board. While ink stamps do seem the way to go, smudging also seems like an inevitability now and then. Especially in my case...

What about (laser) printing onto an appropriate paper, then simply dry mounting (if that's one's mounting choice to begin with) onto the back of the mount? This could be done as a single sandwich in a single pass through the press. If it's permanent for the print - some might say too permanent - it should be likewise for the information sheet. However, I'm not knowledgable regarding the keeping properties and longevity of fused toners.

Ken

You don't want to use a laser printer, laser printers use a plastic powder (toner) that is heated to melt it into the paper, if the mounting press is hot enough, it can melt the printing and make for either a poor image, or a mess in the press. An ink jet printer would be better for this kind of thing, the inks are typically not affected as much by heat. Another option would be to make up an artwork, with several copies, photograph the artwork, print that is a photograph, cut them apart and attach one to the back of the mat. Use a chemically inert pen or marker to fill in the details.

 

[Victor Krag]

http://www.thestampmaker.com/wood_handle.aspx

I bought a 4 x 3" from this company, works great.

http://www.thestampmaker.com/wood_handle.aspx

Good luck,

 

[Victor Krag]

http://www.thestampmaker.com/wood_handle.aspx

I bought a 4 x 3" from this company, works great.

http://www.thestampmaker.com/wood_handle.aspx

Good luck,

 

[PHOTOTONE]

If you want to stamp your prints, you need a "rubber stamp". These are custom made and can usually be sourced from office supply stores, or you might look in your phone directory under rubber stamps. Bear in mind that while common ink pads for rubber stamps will work with fiber prints, the ink will not dry very well on RC prints (as it dries by absorption). There has been specific ink made for RC and plastic stamping. the office supply store may not be able to source it. You can get dry stamp pads and add whatever ink you want to them.

I see you live in LA. You should be able to find many vendors for custom rubber stamps there. You might even find one with 24 hour service. (turnaround).

 

[phc]

What sort of paper are the prints? A self-inking stamp will never dry on a coated surface, i.e. a resin coated paper, as the ink relies on absorption and does not evaporate. I had to buy a simple "traditional" style stamp and a pad, and special stamp ink that evaporates quickly.

Cheers, Paul.

 

[jovo]

...but like any other adhesive sticker, I'm sure they'll turn yellow and/or deteriorate over time. Correct me if I'm wrong......

More than 7 years have elapsed since this thread began. The Avery labels on my prints look just as they did when I applied them...no yellowing or other deterioration. I wish I could say the same for my face!