Speed graphic rangefinder repair

michr

Member
Joined
Sep 28, 2012
Messages
440
Format
Multi Format
I had accidentally bent the rangefinder plunger on my Speed Graphic. In attempting to bend it back I accidentally pulled it out and BBs went everywhere. The plunger isn't is very good shape now either.

Does anyone know if there's a kit I can buy to repair the rangefinder?

At minimum I'll need to replace the plunger, by that I mean the metal piece which compresses the BBs inside the rangefinder tube. Most likely I've dropped a BB or two, so it would be good to have a full set as well.
 

Paul Cunningham

Member
Joined
Mar 16, 2011
Messages
259
Location
Portland, OR
Format
Multi Format
Ha! This just happened to me too. Except that I think I was able to get it all back together, but minus one BB.
I carefully laid them all out rod-BB-rod-BB and so on. But when I got to the end, there were two rods and the alignment was off. So I feel I've lost one BB.
I could realign the rangefinder but I'd rather replace a BB first.

Could I impose on you for a few bb's and rods? I'd more than happy to pay postage and a little something for your trouble. Maybe a couple sheets of film?

Paul
 
OP
OP

michr

Member
Joined
Sep 28, 2012
Messages
440
Format
Multi Format
How did you manage to get them all back in?
 

Terry Christian

Member
Joined
Dec 2, 2011
Messages
693
Location
Memphis, TN
Format
35mm
The same thing happened to my Crown soon after I got it. Still unrepaired -- I just use it on a tripod as a view camera until some repair option presents itself.
 
OP
OP

michr

Member
Joined
Sep 28, 2012
Messages
440
Format
Multi Format
Your link is very helpful. Do you know a source for the plunger. Should I just try to have one machined?
 

Paul Cunningham

Member
Joined
Mar 16, 2011
Messages
259
Location
Portland, OR
Format
Multi Format
One at a time. I used a bic-type ball point pen with the insides removed. It fit just right over the tube end. It took a couple of tries, be sure to put them in one at a time.
 
OP
OP

michr

Member
Joined
Sep 28, 2012
Messages
440
Format
Multi Format
Awesome, that's something I wouldn't have thought of. I'll give it a try.
 
OP
OP

michr

Member
Joined
Sep 28, 2012
Messages
440
Format
Multi Format
I'll post one later this evening.
 

Paul Cunningham

Member
Joined
Mar 16, 2011
Messages
259
Location
Portland, OR
Format
Multi Format
Terry, do you want to part with a few of the small parts, if you no longer have a complete set of bearings?

Terry Christian said:
The same thing happened to my Crown soon after I got it. Still unrepaired -- I just use it on a tripod as a view camera until some repair option presents itself.
Click to expand...
 

Tom1956

Member
Joined
May 6, 2013
Messages
1,989
Location
US
Format
Large Format
Trying to use balls alone will not work. They will not roll on one another as you might think. Instead they will "crowd" or "cram" for lack of better words in my vocabulary. Whatever way you put it, you would have nothing but a conglomeration of haphazard tangents and never any accuracy. The spacers maintain parallel tangents that follow the curvature of the tube. Gives it just about the same accuracy as you would expect from hydraulics. The balls diameters need to fit the tube, lest they will crowd against one side of the tube under pressure, giving an effective smaller ball diameter..
 

Paul Cunningham

Member
Joined
Mar 16, 2011
Messages
259
Location
Portland, OR
Format
Multi Format
The closest common bearing size would be 7/64" or 0.1094, versus the original spec of 0.1085. With a difference of 1/1000" it's a close approximation. It would be a different story however, if you needed a rod.
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…