RB67 SD rotating adaptor on rb67 pro body?

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 15, 2010

• #1

Is it possible to put an rb67-sd rotating adaptor onto the older rb67-Pro body? I have noticed from photographs that the rb67-sd rotating adaptor has two pins whilst the pro has only one.
I have a 6x8 film back (autowind) and want to get the full 6x8 negative format. With the rb67 pro rotating adaptor I get 6x7.25 negs.
I have searched around for a direct answer to this question but no luck. Thanks.
John

 

CGW

Member

Joined

Apr 19, 2010

Messages

2,896

Format

Medium Format

• Aug 15, 2010

• #2

Isn't the extra pin part of the Pro S/D double exposure lock-out system that the early Pro RB+backs lack? I suspect it would fit without any 2x exposure protection since the old Pro didn't have it. If no one answers, try the MF forum at photo.net.

 

Last edited by a moderator: Aug 15, 2010

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 15, 2010

• #3

Thanks for the speedy reply. I am not sure if the extra pin will prevent the unit from fitting on the old rb67 body and will need some filing down. Anyone out there know the answer?
John

 

CGW

Member

Joined

Apr 19, 2010

Messages

2,896

Format

Medium Format

• Aug 15, 2010

• #4

I 'm curious about the 6x8 back too and found some enlightenment here:

http://photo.net/medium-format-photography-forum/00FJLH

Do snoop around pnet--tons of info archived there.

 

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 16, 2010

• #5

Thanks CGW,
Based on your advice I went back to photo.net and finally found a piece that said the extra pin is not removable and, with it in place, a rb67 pro body cannot accept a rb67-sd rotating adaptor. Mmmm . . . still thinking about it.
John

 

John Koehrer

Subscriber

Joined

Apr 3, 2004

Messages

8,277

Location

Aurora, Il

Format

Multi Format

• Aug 16, 2010

• #6

Everything is removable , if it's chrome, it just unscrews. It may have a sealant on the threads, but vise grips work wonders.

 

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 16, 2010

• #7

Thanks John,
You are absolutely correct of course. I have a couple of cameras in a million pieces to prove it. I have the rotating adaptor on the way. I will let you know my findings.

 

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 21, 2010

• #8

OK Folks.
1. A rb67 Professional rig shoots a 5.6 x 6.8 negative.
2. A rb67 pro body + rb67 pro rotating adaptor + 6x8 power back gives a 5.6 x 7.2 negative.
3. A rb67 pro body + rb67 pro-sd rotating adaptor + 6x8 power back gives a 5.6 x 7.3 negative
And, John, you were correct . . . the pin unscrewed

 

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 31, 2010

• #9

Finally,
If anyone is interested, an RB67 Pro body with the #8 baffle + rb67 pro-sd rotating adaptor + 6x8 power back gives a 5.6 x 7.5 negative.
John

 

CGW

Member

Joined

Apr 19, 2010

Messages

2,896

Format

Medium Format

• Aug 31, 2010

• #10

Whew! Thanks for the update. How's the power drive back in terms of noise, speed and operational smoothness? Have been tempted to get one for my Pro S--like it needs more weight...

 

OP

OP

jtcliff

Member

Joined

Sep 6, 2005

Messages

37

Format

Medium Format

• Aug 31, 2010

• #11

Hi John
It needed a refitted strip of felt at the hinge and latch sides. It is reasonable quiet, reasonably heavy. When you fire the shutter the red counter pops up right after the shot is taken and immediately it winds on. The only problem I have is I have to remember to take out the slide to shoot. If it is not pushed fully home when reinserted after a shot it is possible to cock the shutter and fire and get an unexposed neg.