Omega D-II Alignment and Reassembly Questions

Night Drive 2

D
Night Drive 2

  • 1
  • 0
  • 90
Night Drive 1

D
Night Drive 1

  • 1
  • 0
  • 97
Sonatas XII-49 (Life)

A
Sonatas XII-49 (Life)

  • 1
  • 1
  • 451
市

A

  • 1
  • 3
  • 708
Approaching fall

D
Approaching fall

  • 7
  • 3
  • 1K

Recent Classifieds

Forum statistics

Threads
199,706
Messages
2,795,456
Members
100,006
Latest member
Nadikahapu
Recent bookmarks
0
Joined
Oct 25, 2004
Messages
1,057
Location
Westport, MA
Format
Large Format
I've a pre-war Omega D-II enlarger and am stumped as to the best way to align the bellows/head/lamp assembly to the enlarger rail. You can adjust this assembly with four 'bars' that each have two plastic bushing. The bars are concentric, you can adjust each one for friction and this tilts the entire assembly 'backwards' and 'forwards'. Too tight and you can't really move the head up and down. Too loose and it's 'sloppy'.

Either way I can't get it right. Any old-hands know of a trick? There must be a very simple and easy way of doing this, i'm sure there was some assembly at the Omega factory using nothing more that a tall wooden box and some string. Argh!

Also, anyone know of a suitable replacement for those plastic well bushings? I've seen similar substitutes at Lowe's and online but they aren't exact. If I had a lathe. Ah well.

I'm using a laser level and mirror for alignment and with the head extended at different heights I'm seeing the 'dot' move unproportionally. These plastic bushings are worn and peeling. I'm sure this is the culprit. So many problems. Anyone had this problem?
 

David A. Goldfarb

Moderator
Moderator
Joined
Sep 7, 2002
Messages
19,974
Location
Honolulu, HI
Format
Large Format

Monophoto

Member
Joined
Aug 27, 2004
Messages
1,689
Location
Saratoga Spr
Format
Multi Format
Wasn't there an article in PhotoTechniques a couple of years ago about refurbishing and aligning the DII?
 

Neal

Subscriber
Joined
Dec 3, 2004
Messages
2,020
Location
Chicago, West Suburbs
Format
Multi Format
Dear Phillip,

I think my D-II had little holes drilled through that allow you to use a small bar (I use an allen wrench) to rotate them (I combined it with a basket case Chromega so I'm not sure which parts started where). I snug down the offset axles, rotate until level, then tighten everything up. BTW, you will chase perfect alignment forever. The main beams are not machined to perfection and I'm pretty sure the rollers were less than perfect when brand new. The good news is that you can get it close enough that grain will look sharp all across the print.

Neal Wydra
 
OP
OP
Joined
Oct 25, 2004
Messages
1,057
Location
Westport, MA
Format
Large Format
I've love for the alignment tool, didn't think of that! Neal, thanks for your tips. Mine have holes as well, I am going to try that right now. I think you're right about never getting it perfect. I really wish I had a durst 138. Oh well, this old omega will work just as well. Thanks guys!
 

Will S

Member
Joined
Nov 30, 2004
Messages
716
Location
Madison, Wis
Format
8x10 Format
Having just purchased an alignment tool from Harry I can honestly say that it is well worth it, and that you can get the alignment very close to perfect.

The alignment process is incremental and involves the negative stage, the lens stage and the easel. I found it next to impossible to figure out without Harry's instructions. With his instructions and tool I had it done in about 20 minutes.

Good luck,

Will
 

wilsonneal

Member
Joined
Feb 14, 2006
Messages
598
Location
Northern NJ
Format
8x10 Format
Is Harry's tool the same as the Omega tool?: A long, flat bar (about 14") with an adjustable bubble level? I bought one of these on eBay but it didn't have any instructions. I would love to see a copy of the instructions.
Neal

Having just purchased an alignment tool from Harry I can honestly say that it is well worth it, and that you can get the alignment very close to perfect.

The alignment process is incremental and involves the negative stage, the lens stage and the easel. I found it next to impossible to figure out without Harry's instructions. With his instructions and tool I had it done in about 20 minutes.

Good luck,

Will
 
Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links.
To read our full affiliate disclosure statement please click Here.

PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Ilford ADOX Freestyle Photographic Stearman Press Weldon Color Lab Blue Moon Camera & Machine
Top Bottom