Olympus Trip 35 Repair

Mike Wilde

Member
Joined
Aug 10, 2006
Messages
2,904
Location
Misissauaga
Format
Multi Format
nicely done

I have had my trip apart a couple of years becuase of all things the resistor popped off an end fitting, which put an end to auto metering. It would have been nice to have to see all of the steps to dissassemble it.

In the end my repair was to hold the restistor bits together with a bit of blu-tack.

There is a modification on the web to hook onto the lever that selects 1/40 vs 1/200 shutter spped setting, located under the exposure counter dial and allow you to 'pull a little bit of a ty rap' to allow you to use the camera on manual (ie flash settings) with the 1/200 shutter speed.

I have not yet made this modification, but I have verified that the metghod it discusses will work. I have set this project aside until the day when my other little Oly, the XA dies.
 

yellowcat

Member
Joined
May 19, 2008
Messages
114
Location
Bristol, Eng
Format
35mm
Some good instructions there. (despite some problems I had with loading the page)
I have repaired a couple of trips and a couple of other old Olympus compact cameras, reasonably easy to work on if you are careful, I find it best to cover the work top with a large sheet of white paper before you start just to make it easier to see everything.
 

Mike Wilde

Member
Joined
Aug 10, 2006
Messages
2,904
Location
Misissauaga
Format
Multi Format
felt is my preference

A smooth felt, as you would once have found on a 'card table'. It reduces the risk that little things that drop out don't bounce out of sight.

I ahve also learned to sweep and vaccuum the floor of the area I am working in before starting. It makes sweeping to find the little bit that gets away so much easier. To hold small parts I use empty egg cartons. The lid can be folded over and thus keep dust out if there is a while required before the thing goes back together again.
 
OP
OP

thuggins

Member
Joined
Jan 12, 2008
Messages
1,144
Location
Dallas, TX
Format
Multi Format

Mike, be careful with that shutter speed modification. It will only work if the meter is completely disabled. Remember that the "Flash" setting is not a manual override! If the meter is operating, it will still control the aperture, even in the "Flash" setting. So your exposure will invariably be wrong if you manually override the shutter speed to 1/200sec. That mod might be a good idea if the cell/meter has really crapped out. But I don't believe that is a very likely failure.
 
OP
OP

thuggins

Member
Joined
Jan 12, 2008
Messages
1,144
Location
Dallas, TX
Format
Multi Format
Oh no, Ian!! That only leaves 9,999,997 of them!

Some folks have pointed out that Firefox does not render the site properly. I've reported the problem to them. In the meantime, it seems to work fine in IE.
 

yeknom02

Member
Joined
Feb 4, 2010
Messages
312
Location
Detroit
Format
Multi Format
Hey, I just wanted to thank you (a few years later) for posting this. It seems that you've helped me resurrect this little beauty to keep on shooting.
 

elekm

Member
Joined
Sep 12, 2004
Messages
2,055
Location
New Jersey (
Format
35mm RF
You did a nice job with the detail work and the photos.

The only thing you might want to do is figure out a way to correctly collimate the lens. That is, set infinity focus. If you mate the treads at a different point, then aligning to your previous mark will be incorrect at infinity.
 

Ian Grant

Subscriber
Joined
Aug 2, 2004
Messages
23,249
Location
West Midland
Format
Multi Format
thuggins said:
Oh no, Ian!! That only leaves 9,999,997 of them!

Some folks have pointed out that Firefox does not render the site properly. I've reported the problem to them. In the meantime, it seems to work fine in IE.
Click to expand...

Interesting that the threads been revived as it appears my hoarding instinct saved my two Trip's, and I spotted them last November in storage, they cxan now await their turn in the restoration regime, anything 100+ years old gets priority though

Ian
 

John Hermanson

Member
Joined
Sep 19, 2005
Messages
306
Location
Huntington,
Format
35mm
Infinity focus is adjusted to 1/100th of a mm. Once you unscrew the lens (even if position is marked) infinity focus will be wrong when you reassemble (though depth of field will pull focus in). Was infinity focus correct when you took it apart? A focus collimator is needed to reset lens to proper infinity focus. John
 

kittyhawk88

Member
Joined
Sep 24, 2009
Messages
21
Location
Sydney, Aust
Format
Medium Format
it's quite easy to collimate for inifinity on a trip 35. just place a ground glass on film plane or scotch magic transparent tape and adjust the front element till it all comes into focus with the distance ring set for the mountains..

enjoy.
 

Strider

Member
Joined
Mar 23, 2009
Messages
15
Location
West Linn, O
Format
35mm
Trip 35 repair

Thanks for this great set of instructions. I just dug out my Trip 35. If it does need a repair your instructions will offer me much needed guidance!

thuggins said:
Since I couldn't find a good document for testing and repairing a Trip 35, I just posted a fully illustrated set of instructions.
www.thermojetstove.com/Trip35

Let's keep those little beauties clicking!
Click to expand...
 
OP
OP

thuggins

Member
Joined
Jan 12, 2008
Messages
1,144
Location
Dallas, TX
Format
Multi Format
There are a couple of FTL bodies and a set of lenses in my collection. They are not a bad camera. While certainly not as innovative as the Pen's or OM's, they were on par with the competition of the time. Olympus did advertise the feature of a screw mount lens with full aperture metering. AFAIK, that was a first.
 

frjack

Member
Joined
Jul 24, 2014
Messages
23
Location
Leigh, Lanca
Format
35mm
Thanks for that. It may be useful... If my hands will stop shaking then seizing up, when I try to do delicate jobs.

This message delivered by rolling into a ball and flicking from my knee.
 

Digital Wendy

Member
Joined
Feb 21, 2014
Messages
74
Location
Oxford UK
Format
Multi Format
Hello there @thuggins.
Just dug out an old Trip as a youngster is looking for a point-and-shoot.
Link in this amazing thread seems to have stopped working . Do you , by chance, have those instructions stored anywhere else?
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
51,947
Location
Delta, BC Canada
Format
Medium Format

reddesert

Member
Joined
Jul 22, 2019
Messages
2,316
Location
SAZ
Format
Hybrid
Matt, that's the user's manual for a Trip 35. Tim Huggins's link was on how to repair a Trip 35, but his previous domain may have stopped working. Should the repair document be needed, the Internet Archive is often a good place to look for such webpages, and it does have useful results: https://web.archive.org/web/20230602214407/http://www.thermojetstove.com/Trip35/

The Internet Archive needs our support and donations too, BTW.
 

MattKing

Moderator
Moderator
Joined
Apr 24, 2005
Messages
51,947
Location
Delta, BC Canada
Format
Medium Format
Thanks.
I took the request for "instructions" as meaning the user manual.
Thanks for helping find an example of the repair manual.
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…