Mixing developer and paper tones

Jim_in_Kyiv

Member
Joined
Apr 7, 2005
Messages
231
Location
Ukraine
Format
Med. Format RF
I've finally put my darkroom back together, and did my first contact prints last night. It's a pleasure to be back. However, I'm wondering about mixing warm and cold tone components. I've got left over warm and neutral(?) tone paper sitting around, but the only paper developer I've seen in town is cold-tone. Last night I worked with a high-contrast image on Tech Pan - something I think would have been pretty cold in tone to begin with, so the results didn't surprise me. However, if I start using the warm tone paper (Ilford MG, IIRC), will the result be rather neutral? I just don't have anything at home to compare to execpt for the image on the paper container.
 
Last edited by a moderator:

David A. Goldfarb

Moderator
Moderator
Joined
Sep 7, 2002
Messages
19,974
Location
Honolulu, HI
Format
Large Format
The main issue might be that some developer/paper combinations can produce high base fog, which isn't really acceptable in a print developer (the whites should be clean).

You might also get a tonality you don't like, but that's hard to predict without testing, and it might be correctable with toning.

Try it out, and see what happens.
 

Roger Hicks

Member
Joined
May 17, 2006
Messages
4,895
Location
Northern Aqu
Format
35mm RF
Dear Jim,

Tone and contrast should not be interdependent, and the neg should have no effect on tone. Are the devs advertised as 'cold tone' or merely normal, i.e. not warm-tone? Because some warm-tone developers aren't as warm with MG WT as non-WT developers, believe it or not.

Did you consider mixing up some of that phosphoric acid developer I recommended as a cure for rusty photographic skills?

Cheers,

Roger
 
OP
OP

Jim_in_Kyiv

Member
Joined
Apr 7, 2005
Messages
231
Location
Ukraine
Format
Med. Format RF

More learning! The dev is Forte Cold Tone Paper Developer. I can't remember what I used before - this is the first time I've printed in 4-5 years, except for once with some powdery paper developer from Svema or similar. Luckily, I developed negs regularly since I moved here.

Tone and contrast are interdependent in my mind, or were until I started using my brain again. It was a matter of my expectations for the print that got carried over.

Base fogging if one mixes warm and cold tones? The whites (i.e. clouds that I was paying attention to) were pretty good, but as I go through the paper odds and ends that I have I'll pay attention to it.


I had thought about using phosphoric acid developer as a cleaner for some of the darkroom accessories that had become rusty somehow. On second thought, I figured that I was entitled to soak them in WD-40 like a good American, now that the stuff is available over here. But while they're soaking, I was considering making up a batch for my own rustiness. Glass trays, of course.
 

Roger Hicks

Member
Joined
May 17, 2006
Messages
4,895
Location
Northern Aqu
Format
35mm RF
Jim_in_Kyiv said:
Base fogging if one mixes warm and cold tones? The whites (i.e. clouds that I was paying attention to) were pretty good, but as I go through the paper odds and ends that I have I'll pay attention to it.
Click to expand...
No inherent reason why. In fact, I'd expect worse fogging with cold-tone (faster paper, faster developing) with any given developer, but perhaps that is merely a demonstration of my ignorance.
 

DrPablo

Member
Joined
Aug 16, 2006
Messages
814
Location
North Caroli
Format
Multi Format
I've read Tim Rudman's toning book, and if I recall correctly (and my own experience is consistent with this) warm tone papers are far more amenable to toning overall including from cold tone developers and toners. Warm tone papers may well give a warm tone if developed in warm tone developers; but they are also more amenable to cold tone developers and cold toners like selenium and gold.

Cold tone papers will indeed look cold, but it tends to be a steely, icy cold look -- the tone is enough to give it mood without really giving it color.

I think fogging is a separate issue. With normal paper developing (i.e. not lith developing) the vast majority of contrast control comes from the exposure (including filters), and the paper development plays a very small role. If there is fogging, I'd look to other issues before the developer (i.e. is the negative fogged, is the paper pre-fogged, are you using the right grade contrast filter, etc).
 
Last edited by a moderator:

dancqu

Member
Joined
Sep 7, 2002
Messages
3,649
Location
Willamette V
Format
Medium Format
Warm Tone PAPER from Snow White

PAPER to distinguish twixt Image and Paper.
This is an aside.

Working to find the exact amount of fixer needed to
completely fix a sheet of paper I found that if the amount
is a little shy the paper assumes a tone after some exposure
to light. The tone depends upon the paper. Arista and Kentmere
Bromide Graded FB papers take on a very pleasant warm hugh
while the same in Emaks becomes a dirty very light gray.

Slavich Graded FB is still a question mark. Seems that some
papers take considerable less or more fixer to clear. Kentmere
Bromide is the fixer hog taking 1/3 more than the Arista and
Emaks and 1/2 or more fixer than the Slavich.

So, warm from white with less than enough fixer. Illuminating
I think if nothing more. Dan
 

Dan Henderson

Member
Joined
Feb 6, 2005
Messages
1,880
Location
Blue Ridge,
Format
4x5 Format

Doesn't this "tone" imply insufficient removal of undeveloped silver, in which case the "tone" will continue to develop in light to ruin the print?
 

David A. Goldfarb

Moderator
Moderator
Joined
Sep 7, 2002
Messages
19,974
Location
Honolulu, HI
Format
Large Format
The reason I bring up base fog is that with some of the Efke papers, it was recommended to avoid soft and warmtone developers, because they produced more base fog than more energetic developers. I also found that this could happen with Oriental Seagull graded and Agfa Neutol WA.
 

Roger Hicks

Member
Joined
May 17, 2006
Messages
4,895
Location
Northern Aqu
Format
35mm RF

Dear David,

That's weird. You'd surely expect more fog from a more energetic developer. Any ideas on how it happened?

Cheers,

Roger
 

David A. Goldfarb

Moderator
Moderator
Joined
Sep 7, 2002
Messages
19,974
Location
Honolulu, HI
Format
Large Format
I'm not sure. I think it may be just the fact that a more energetic developer is usually a higher contrast developer, so the shadows will come in faster than the highlights, and development time for normal contrast will be shorter, giving less time for base fog to appear. It might also just be some other chemical interaction, but I'm not sure offhand what that might be.
 

dancqu

Member
Joined
Sep 7, 2002
Messages
3,649
Location
Willamette V
Format
Medium Format
FirePhoto said:
Doesn't this "tone" imply insufficient removal of
undeveloped silver, in which case the "tone" will
continue to develop in light to ruin the print?
Click to expand...

Less than enough fixer for complete fixing does
leave some silver in the emulsion. Only so much of
a hugh will develop as is silver retained. To warm a
paper in such a manor may be realistic.

A twist on that approach would be toning the residual
silver left in the emulsion. In that way the base paper
could be made any color. Needless to say the image
silver would be affected. Then again any off shelf
warm tone base paper will impart to some
degree a warmth to the image. Dan
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…