Minolta x300 - Film Advance Lever Problem

[kd218]

Hi! This is my first post so I thought I might give it a try since reddit and youtube did not help at all.

I have a Minolta x300 loaded with a film. However, the film advance lever stops working mid-film so that I cannot do anything at all. Batteries are changed and also checked for any battery corrosion (seems fine). Any guesses what else I can check for?

Thanks!

 

[Andreas Thaler]

Welcome!

I would first secure the film and remove it from the camera.

Release the rewind lock and rewind the film, but do not pull it all the way into the cartridge, then you can continue to use it.

Then the 300 can be examined further.

 

[Andreas Thaler]

The camera is obviously blocked because one of the steps in the sequence of actions from winding to release has not been completed.

I could imagine the following:

• The shutter is not completely closed, this happens with X cameras. This can be fixed by gently and carefully pulling on the shutter curtain.
• The electrolytic capacitor in the bottom of the camera is defective, also a common fault. This is often recognizable by the LEDs in the viewfinder going out after pressing the shutter button.
• The film is blocking the transport because it is not wound correctly onto the take-up spool. This should be fixed by rewinding the film.
• Part of the mechanism is defective. Rather unlikely.

 

[kd218]

Welcome!

I would first secure the film and remove it from the camera.

Release the rewind lock and rewind the film, but do not pull it all the way into the cartridge, then you can continue to use it.

Then the 300 can be examined further.

Thanks! Will give it a try, although the film counter is broken on this on.

 

[kd218]

The camera is obviously blocked because one of the steps in the sequence of actions from winding to release has not been completed.

I could imagine the following:

• The shutter is not completely closed, this happens with X cameras. This can be fixed by gently and carefully pulling on the shutter curtain.
• The electrolytic capacitor in the bottom of the camera is defective, also a common fault. This is often recognizable by the LEDs in the viewfinder going out after pressing the shutter button.
• The film is blocking the transport because it is not wound correctly onto the take-up spool. This should be fixed by rewinding the film.
• Part of the mechanism is defective. Rather unlikely.

wow, thanks a lot! That's the second this has happened so will try the steps again and hope for the best as repair costs are too high

 

[xkaes]

As Andreas has pointed out, given the age of the camera there is a good chance the capricious capacitor caved.

You can test this as Andreas mentioned -- once you get the film out. Make sure the camera is OFF, with a good battery installed. Set the camera shutter dial to "A". Turn the camera on. While looking through the viewfinder, press the shutter release slightly to see if any LED lights up. Press it all the way, and see if it goes out. If it does, the capacitor is the problem. If the shutter fires, no problem.

Capacitors are cheap and you can replace it yourself if you have the tools, materials, the time, and some soldering experience. A repair shop can do it, but it will probably cost more than a working body. FYI, the X-300 was also sold under several other names. See --

http://www.subclub.org/minman/x370.htm

 

[Andreas Thaler]

Maybe these posts will help, I was, among other things, concerned with a shutter issue and replacing the electrolytic capacitor:

Minolta X-300 put back into service

An X-300 with some signs of wear and a dent on the side of the top cover, a bit dirty - a basement find, as the previous owner told me. The shutter is cocked, the LEDs in the viewfinder remain dark when the trigger is tapped, pressing the trigger does not release the shutter. Ok, let's see...

www.photrio.com

Electrolytic capacitor replacement on a Minolta X-300s

Of the 13 Minolta X cameras that are waiting to be checked here, see https://www.photrio.com/forum/threads/interested-in-minolta-x-camera-repair-reports.202857/#post-2739628 I was able to get candidate 1/13, a Minolta X-300s back to work 🙂 Issues: - Camera cannot be wound up. - LEDs in the...

www.photrio.com

Minolta X-700/500/300 (700/570/370): Recommendations and notes

Timeless, robust and reliable classics: the three Minolta X SLRs from the 80s Based on my previous (repair) experiences with the Minolta X-700/500/300 (X-700/570/370) cameras with regard to preservation/problems/repair options, I would like to give a summary of the following...

www.photrio.com

 

[MattKing]

Welcome to Photrio.
Is there any chance that you have reached the end of the film?

 

[randyB]

Before rewinding be sure to note the number of exposures that were taken and then write that number on the emulsion side of the film once you remove it from the camera. The emulsion side is lighter so you can see the #, use a Sharpie pen. That is what I do.