Jobo ATL 3000 display dead or repairable?

Paintin' growth

D
Paintin' growth

  • 0
  • 0
  • 2
Spain

A
Spain

  • 1
  • 0
  • 5
Machinery

A
Machinery

  • 6
  • 3
  • 73
Cafe art.

A
Cafe art.

  • 1
  • 7
  • 97

Forum statistics

Threads
198,097
Messages
2,769,545
Members
99,561
Latest member
jjjovannidarkroom
Recent bookmarks
1

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
Hi,
My ATL3000 display functioned well before the summer and after not using it for two months, I noticed that yesterday three out of four buttons don't work anymore. What could be the problem and is there a way of fixing this?
Thanks for your thoughts.
Albert
JOBO.jpg
 

AgX

Member
Joined
Apr 5, 2007
Messages
29,973
Location
Germany
Format
Multi Format
What do you mean by the buttons not working any more?

-) having no effect on the process

-) resp. figures not showing up


Depending on the above, it may be faulty switches, bad contacts at the display, a fault at the CPU.
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
What I mean is, when I press those three buttons, in the red circle, they don't make contact. No sound and no effect on the LCD screen or process. The first triangle, at the left, works fine.
 

AgX

Member
Joined
Apr 5, 2007
Messages
29,973
Location
Germany
Format
Multi Format
So we can exclude the display.
Foil switches of course may fail. However hardly 3 at same time. The next thought would be the contacts or wiring of the switches-board. Here one may ask why 3 switches fail and one still works. Otherwise one may have considered failure of a common track (eg. ground).
I would take out that board and have a closer look at its circuit.
If this seem ok, the next stage to investigate would be the CPU...
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
Ok thanks, will take a look at that.
Hopefully it's not the CPU, I have no knowledge in that domain...
 

AgX

Member
Joined
Apr 5, 2007
Messages
29,973
Location
Germany
Format
Multi Format
In that case only the LCD display or part of it would be dead. That is why I asked on the processing. On this the repective 3 switches are of no effect neither.
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
I've taken out the control board and mesured the resistance off the switches and they don't seem to work at all...
In the mean time I found an adress in Germany of Herrn Klaus Seynsche who might have spare parts for these machines. I just send him an email to see if he can help me.
 

AgX

Member
Joined
Apr 5, 2007
Messages
29,973
Location
Germany
Format
Multi Format
Alternatively you could exchange all switches for classic momentary switches.


(Still strange that 3 switches fail at a time.)
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
Yes I agree, it's strange...
I've thought of changing the switches but I don't know how to fix them on the flat ribbon cable?
 

AgX

Member
Joined
Apr 5, 2007
Messages
29,973
Location
Germany
Format
Multi Format
I'm ignorant on that assembly, but in case of re-building as repair I would either mount push-switches on the current board after cutting out those foil switches or alternatively make new small board just for the switches and mount and seal it on the current board or make a complete new board including main switch and display and inserit it instead in the casing. And then make the connections by soldering the respective strands of the ribbon cable to the switches, if needed lenghtened by wires.
 

shutterfinger

Member
Joined
Feb 25, 2013
Messages
5,020
Location
San Jose, Ca.
Format
4x5 Format
I've taken out the control board and mesured the resistance off the switches and they don't seem to work at all...
I've thought of changing the switches but I don't know how to fix them on the flat ribbon cable?
Either the metal has tarnished or /worn through. Flushing with 90% Alcohol or contact cleaner should correct tarnished contacts at least temporally but worn contacts will require switch replacement as I doubt they were designed to be repaired. Also check that the cable has not failed.
 

mshchem

Subscriber
Joined
Nov 26, 2007
Messages
14,422
Location
Iowa City, Iowa USA
Format
Medium Format
I would call Omer Hecht at Catlabs. Also there are still a couple folks who work on Jobo. Don't mess it up until you have no choice. The switches could be dirty or gummed up.
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
I got an email back yesterday from M Seynsche and he told me he has spare parts but is on holidays untill the endof next week.

Flushing with 90% Alcohol or contact cleaner should correct tarnished contacts at least temporally but worn contacts will require switch replacement as I doubt they were designed to be repaired

Maybe it's doable but it's sealed in plastic and it seems to me quite troublesome to do it and to make it waterproof afterwards and that it will still fit in its original place well... I think it's not meant to be repaired :-(
 

mshchem

Subscriber
Joined
Nov 26, 2007
Messages
14,422
Location
Iowa City, Iowa USA
Format
Medium Format
I got an email back yesterday from M Seynsche and he told me he has spare parts but is on holidays untill the endof next week.



Maybe it's doable but it's sealed in plastic and it seems to me quite troublesome to do it and to make it waterproof afterwards and that it will still fit in its original place well... I think it's not meant to be repaired :-(
Sounds like you have a solution. Get the parts. That's quite the machine.
 

jim10219

Member
Joined
Jun 15, 2017
Messages
1,632
Location
Oklahoma
Format
4x5 Format
They're near the on/off switch which appears to have an opening below. It's possible that some liquid got in there and spread over those switches and corroded them. Since you're replacing the switches anyway, you might as well check around while you're in there for any more corrosion. Often times liquid exposure can start corrosion on a board and even after the liquid dries, the corrosion can spread. If that's the cause and you don't fully clean it out, you risk losing the other switch and possibly the display. Though it's hard to say anything without looking at the circuit itself.
 

Raphael

Subscriber
Joined
Jul 26, 2006
Messages
416
Location
Europe, Fran
Format
Multi Format
I got an email back yesterday from M Seynsche and he told me he has spare parts but is on holidays untill the endof next week.

Hi,
I am glad to know that Herr K.D Seynsche is still on the circuit. If you can, can you give me his email address, please ? The last time I contacted him was through his business site, and it went down since.
BTW, any progress with your ATL3000 repair ?
In advance, thanks you,
Best regards,
Raphael
 
OP
OP

albertphot

Member
Joined
Jul 4, 2007
Messages
37
Location
Angers, F (G
Format
Multi Format
Hi, I repaired my ATL last week!

Herrn Seynsche was very quick with sending me the new displayboard, but I had no time reparing my ATL untill last week.

It works now as before, I couldn't find any corrosion marks on the old one strangly...

His E mail adress is; kds@fotolaborservice.de

He reply's very quickly, even while he was on holidays!!!

Good luck!
 
Last edited:

Raphael

Subscriber
Joined
Jul 26, 2006
Messages
416
Location
Europe, Fran
Format
Multi Format
Hi, I repaired my ATL last week!

Herrn Seynsche was very quick with sending me the new displayboard, but I had no time reparing my ATL untill last week.

It works now as before, I couldn't find any corrosion marks on the old one strangly...

His E mail adress is; kds@fotolaborservice.de

He reply's very quickly, even while he was on holidays!!!

Good luck!
@albertphot : Glad you have now a full functional ATL !
Thanks you very much for KD email :smile:
I also repaired my ATL1 this week, but I will need probably a spare themperature probe in a near future..
Thanks again,
Regards,
Raphael
 
Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links.
To read our full affiliate disclosure statement please click Here.

PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Ilford ADOX Freestyle Photographic Stearman Press Weldon Color Lab Blue Moon Camera & Machine
Top Bottom