Is my Zuiko lens dead ? (slight play) (still usable ? fixable ?)

[mcafeejohn]

Hello everyone,

Today, on my OM Zuiko MC 50mm f1.4 lens I noticed an abnormal "play" (i don't know if it's the right word in English) from back to front at the base of the silver ring,
the whole lens moves slightly forward and backwards on about half a millimeter, you can even hear a slight "click" when you do it, it won't move much more than about half a millimeter but I'm worried it might be enough to mess up the focus, maybe even create a light leak inside the lens?
I've included a picture with this post describing where the problem is located,
I wonder if by pushing it "closed" well every time i use it i can still use it normally ? maybe the damage is too much and even when i push it it's still not in its exact original position ?
Am I better off selling it for parts or going to a repair shop, even tho i don't have much hope they'll be able to do anything ?
I would really like to keep using it because it wasn't easy finding an MC version of this lens and i don't think i'll be able to find another one in good condition soon.

If you have any idea and advice or if you had similar experiences with such lenses it would really help,

Thanks !

 

[Ulrich Drolshagen]

Don't know whether mine is MC, the serial number is about 720,000. There is no longitudinal movement.

Ulrich

 

[John Salim]

I'm wondering if there's a loose screw or screws under the rubber focus grip ?

John S

 

[mcafeejohn]

I'm wondering if there's a loose screw or screws under the rubber focus grip ?

John S

could i remove it without damaging it to check ?

 

[John Salim]

You can usually slide a flat bladed knife under the rubber grip, though there's also probably some glue to get through.
But before attempting that, I'd strongly suggest you wait for someone with actual experience to reply to your opening query.

John S

 

[Daniel Stuefer]

It sounds like the mount flange screws could be loose, they are on the back of the lens:

 

[Harry Callahan]

You could take a look at the lens mount. The mount often is screwed to the lens barrel and if these crews are loose you could have the effect you describe.

 

[Ian C]

Is the entire lens moving forward and back relative to the lens mount? To check it, mount the lens on the camera and try to move the front of the lens forward and back without rotating the focusing ring.

If it moves without rotating the focus ring, then you have a problem that must be corrected. If on the other hand, only the aperture preset ring moves independently of the lens, then focus is unaffected, and you need only address the looseness of the aperture ring. To get at the aperture ring, the screws holding the lens mount to the barrel must be removed.

Use only a JIS (Japan Industrial Standards) screwdriver of the appropriate size as other cruciform-socket tools have a different geometry and won’t fit the socket properly and would likely damage the screw sockets.

If the lens mount is loose, then tightening the screws should eliminate the problem.

 

[mcafeejohn]

Is the entire lens moving forward and back relative to the lens mount? To check it, mount the lens on the camera and try to move the front of the lens forward and back without rotating the focusing ring.

If it moves without rotating the focus ring, then you have a problem that must be corrected. If on the other hand, only the aperture preset ring moves independently of the lens, then focus is unaffected, and you need only address the looseness of the aperture ring. To get at the aperture ring, the screws holding the lens mount to the barrel must be removed.

Use only a JIS (Japan Industrial Standards) screwdriver of the appropriate size as other cruciform-socket tools have a different geometry and won’t fit the socket properly and would likely damage the screw sockets.

If the lens mount is loose, then tightening the screws should eliminate the problem.

Yes, when i attach the lens to the body of the camera the entire lens moves relatively to the silver ring, i'll try to tighten the screws Daniel suggested tonight if i still have the right screwdriver and get back to you

It sounds like the mount flange screws could be loose, they are on the back of the lens:

I just hope it isnt related to a drop or something else from the previous owner but from what he said he barely used it and it doesnt look like it took any drop (no marks on the body of the lens)