HC-110 and TMAX 400

Does anyone have a good starter set of Normal, Plus and Minus times for TMAX 400 Roll Film in HC-110?

See http://www.covingtoninnovations.com/hc110/ and the links from there to other sites with HC-110 times/dilutions/temps.

Lee

No joy on the Massive Development Chart site?

Colin Corneau said:

No joy on the Massive Development Chart site?

Click to expand...

Not for plus and minus times.

Kodak publishes data sheets on their films, Publication F-32 in the case of TMax films. Here's page 13.

Lee

The old adage goes, multiply normal time by 1.4 for a plus development, and divide by 1.4 for a minus time. These would be starting points. But with the normal being 5.5 for TMY at 400, that would yield a too short time for the minus. Perhaps a greater dilution for the minus.

A year ago, I bought a Hasselblad camera, so I decided to test TMAX400 (120) and HC110 for this camera. These are the results that I found:
Film: TMAX400.
EI 250
Pre-washed: Water, during 1 minute of constant agitation.
Developer: HC110 (E- 1:47)
Developed two rolls of film, continuous agitation during the first 30 seconds, and then 3 times each 30 seconds.
Time of developing: 8 minutes.
Temperature: 20ªC.
Stop bath: Tetenal Stop, 1:19, and 1 minute with constant agitation.
Fixer bath: Tetenal, 1:9, 10 minutes. The first minute with continue agitation, and then 5 times each 30 seconds.
Results:
After having taken pictures of a Kodak grey card, I found the following relative densities:
Zone 8: 1,25
Zone 5: 0,63
Zone 1: 0,10
These densities have been measured with my RH Designs Analyzer Pro. Theoretically, if you work with a condenser enlarger, like my case, a good exposed and developed film should have the following relative densities: ZI: 0.08 - 0.11 / ZV: 0.60 - 0.70 / ZVIII: 1.15 - 1.25.

Some months ago, I completed this test with the following results:
N+1:
Developed: 9.5 minutes.
Zone 1: 0,10
Zone 7: 1,25

N-1:
Developed: 6.5 minutes
Zone 1: 0,10
Zone 9: 1,25

I hope this information could be useful for you and anybody in this forum.
Henry.

This is an excellent combination. I shoot 35mm and 120 TMY at 250 and develop 1:50 from concentrate, 9 minutes @ 68 degrees. For agitation I give three inversions of the tank at the beginning of each minute.

Michael R 1974 said:

Henry, I'm a little surprised your Zone 1 density is the same for N-1, N, N+1 rating the film at EI 250 in all cases. TMY is a straight line film with a short toe so Zone 1 tends to move as development times are altered. Just a thought.

Click to expand...

For what it's worth----with my tests for TMY and TMX Zone I densities do not change appreciably until the +2 and -2 dev time----in both cases about a 1/3 stop off the measured speed, I'm not surprised at those results. With T-grain film, I consider 1/3 of a stop to be an appreciable difference.

Michael R 1974 said:

Henry, I'm a little surprised your Zone 1 density is the same for N-1, N, N+1 rating the film at EI 250 in all cases. TMY is a straight line film with a short toe so Zone 1 tends to move as development times are altered. Just a thought.

Regards
Michael

Click to expand...

I do not have a densitometer. I work with the Analyser from RH Designs. Usually, I take different measures of the density in the same negative photo, and I get measures of 0.09 – 0.11 -0.12 – 0.10 for Zone I. They go in this order. For this reason, I say 0.1 is the density in Z1.
Henry.