For Trade FT a few sundry items

KennyMark · Feb 21, 2016

A few things that I don't need.
Offer what you have in trade that you don't need, or a cash offer if you'd prefer.

Yashica TLR lens cap -sold

Bronica 6x6 220 insert

Bronica 645 220J insert (broken - crack in plastic frame)

Bronica dark slide for 645

49mm metal lens hood (unmarked)

canvassy · Feb 22, 2016

The Yashica lens caps, do you know what models that fits? I have a Yashicamat LM that needs a lens cap.

frank · Feb 22, 2016

I'd be interested in the Bronica dark slide, but I'm near Toronto, Canada.

Does it measure 66x86mm? I have an S2a.

Edit: this isn't from an S2a but wonder if it will still fit?

KennyMark · Feb 22, 2016

canvassy said:
The Yashica lens caps, do you know what models that fits? I have a Yashicamat LM that needs a lens cap.

I do not, I can give you specific measurements on the backside if you'd like.

Viewing lens rim 23 mm dia.
Exposing lens rim 22mm dia.
Gap between rims 11mm

canvassy · Feb 22, 2016

KennyMark said:
I do not, I can give you specific measurements on the backside if you'd like.

It actually looks like the original from the Yashicamat LM. Do you know if it's a Bay 1 or not?

Also, what would you be looking for in a trade?

KennyMark · Feb 22, 2016

KennyMark said:
I do not, I can give you specific measurements on the backside if you'd like.

canvassy said:
It actually looks like the original from the Yashicamat LM. Do you know if it's a Bay 1 or not?

Also, what would you be looking for in a trade?

It is a bayonet mount.

If you will be using it rather than reselling, I'm happy with something that you have but don't need. Filter, cable release, lens board, negative carrier, 120 or sheet film. I shoot Nikons, Mamiya 645, RB67, 4x5, 8x10. It doesn't need to be valuable, but look around and see what you have but don't need. You can PM me if my inbox will take it.

KennyMark · Feb 22, 2016

frank said:
I'd be interested in the Bronica dark slide, but I'm near Toronto, Canada.

Does it measure 66x86mm? I have an S2a.

Edit: this isn't from an S2a but wonder if it will still fit?

Based on that, I suspect it's from a 645. Dimensions of the visible part of the metal are

65mm high
76mm long in the center
77mm long at top and bottom

And I will mail to you in CA Frank. Heck, you're nearly straight East of me, not North!

frank · Feb 22, 2016

KennyMark said:
Based on that, I suspect it's from a 645. Dimensions of the visible part of the metal are

65mm high
76mm long in the center
77mm long at top and bottom

And I will mail to you in CA Frank. Heck, you're nearly straight East of me, not North!

Thanks Mark! The slide won't fit my camera.

canvassy · Feb 22, 2016

KennyMark said:
I do not, I can give you specific measurements on the backside if you'd like.

Viewing lens rim 23 mm dia.
Exposing lens rim 22mm dia.
Gap between rims 11mm

It looks like the Bay 1 filters are roughly 30mm or so? I'm not sure if that will fit, I've never had a lens cap for this Yashicamat LM, so I don't have anything to compare it to.

KennyMark · Feb 22, 2016

canvassy said:
It looks like the Bay 1 filters are roughly 30mm or so? I'm not sure if that will fit, I've never had a lens cap for this Yashicamat LM, so I don't have anything to compare it to.

This works like the cap for a Minolta Autocord. The bayonet tabs fit inside the rim of the viewing lens. You rotate the cap approximately 45 degrees counter clockwise, insert the top half of the pair into the lens rim, rotate 45 degrees clockwise, then snap the exposing lens cap into place.

canvassy · Feb 22, 2016

KennyMark said:
This works like the cap for a Minolta Autocord. The bayonet tabs fit inside the rim of the viewing lens. You rotate the cap approximately 45 degrees counter clockwise, insert the top half of the pair into the lens rim, rotate 45 degrees clockwise, then snap the exposing lens cap into place.

Right, but the diameter of my bayonet mount is 30mm. 23 isn't going to fit. Do you happen to know which TLR the lens cap came from?

KennyMark · Feb 23, 2016

canvassy said:
Right, but the diameter of my bayonet mount is 30mm. 23 isn't going to fit. Do you happen to know which TLR the lens cap came from?

Hi,
No, I do not know the model that this cap is for. For the sake of clarity, and I expect that we have already have a common understanding, the dimensions I gave are O.D. for an edge that fits inside the rim of the lens. So if the 30mm dimension is I.D., then you are certainly correct. If your 30mm is O.D., then it is possible that it may fit. But as I said, I think that we are already on the same page.

KennyMark · Feb 23, 2016

KennyMark said:
Hi,
No, I do not know the model that this cap is for. For the sake of clarity, and I expect that we have already have a common understanding, the dimensions I gave are O.D. for an edge that fits inside the rim of the lens. So if the 30mm dimension is I.D., then you are certainly correct. If your 30mm is O.D., then it is possible that it may fit. But as I said, I think that we are already on the same page.

Out of curiosity, I tested this cap on a Minolta Autocord and the bayonet half fits but the Yashica cap is just a mm or two too long to snap the bottom half in place.

canvassy · Feb 23, 2016

KennyMark said:
Out of curiosity, I tested this cap on a Minolta Autocord and the bayonet half fits but the Yashica cap is just a mm or two too long to snap the bottom half in place.

Definitely sounds like a Bay 1 then, I'm going to PM you right now

canvassy · Feb 26, 2016

The lens cap arrived today, and it fits my Yashicamat LM

Thank you KennyMark!

KennyMark · Mar 26, 2016

Bump...offers?

KennyMark · Apr 3, 2016

For Trade FT a few sundry items

Privacy & Transparency

Privacy & Transparency