First attempt at processing color slide film????

stradibarrius · Nov 21, 2010

I have never tried to process color slide film. I have processed my own C-41 and of course tons of B&W.

Is it difficult? I know Freestyle has kits available.

sandholm · Nov 21, 2010

Do you have a processor or do you develop your C-41 by hand/tank. Slide is very very temperatur dependent and a processor makes slide processing a piece of cake. I use a Jobo and it works perfect.

markbarendt · Nov 21, 2010

I've only used Kodak's kit. Got my last one here http://www.libertyphotoproducts.com/product/KODAK-Single-Use-Chemistry-Kit-Proc-E-6-5-L,3442,573.htm

The first film I developed when coming back to film was E-6 and it worked, I was truly amazed.

Since you have done C-41 you understand how to get the temp right, there are more steps to E-6 but it is not "tougher."

I stayed away from the "blix" type kits because it didn't really save me anything, including money, the blix kits actually cost more per liter/roll.

Diapositivo · Nov 21, 2010

I begun processing slides without any previous processing experience (not even a B&W roll). It worked, so it should not be difficult.
I have a Jobo CPP-2 which takes care of temperature and agitation. With such a machine, everything is very easy.
Without a machine you have to find a way to keep temperature constant for around 7' and you have to device an agitation strategy that is perfectly repeatable. Some people develop slides without any special apparatus and they refer satisfaction with the results.

The other baths are easy because they are "to completion" and so if your baths are a few °C less than they should you just prolong the bath.

Fabrizio

stradibarrius · Nov 21, 2010

I use a hand tank. I'm going to give it a try and see. Mark I looked at the kit you linked above. Is it easy to process a roll or two with out wasting chemistry???

markbarendt · Nov 21, 2010

Yes,

http://www.kodak.com/global/en/professional/support/techPubs/ti2443/ti2443.pdf

Page 1 shows the mixing.

bdial · Nov 21, 2010

Though I have a Jobo, most of my E-6 processing has been with standard SS tanks. Just use a water bath, it's no harder than C-41 really.

Jeff Kubach · Nov 21, 2010

I have process color and B&W but never slide film, one of these days I will.

Jeff

stradibarrius · Dec 13, 2010

Mark,

when you first posted this answer, I followed the link and it took me to a kit just like you said...but now it just takes me to the website and there seems to be no kits listed????

Mainecoonmaniac · Dec 13, 2010

E6 to me is like eating in a fancy restaurant when you're a good cook. It's better to let someone else do it because it's so complicated eventhough the cook could do it. It may be worth it if you have a large batch, for a roll or two, it's not worth it. Take a look at this link:
http://en.m.wikipedia.org/wiki/E-6_process?wasRedirected=true

stradibarrius · Dec 13, 2010

How much difference is there in the end result of slide vs. print film give todays available films?
Assuming the negatives are to be scanned and printed digitally opposed to needing slides for a presentation.

brucemuir · Dec 13, 2010

Strad,
The Kodak Single Use 5l kit has been discontinued

hpulley · Dec 13, 2010

Slide film has narrower exposure latitude and underexposed slides tend to be very thin and difficult to scan in my opinion. One of my old Canon FD body's ight meter is out by a half to a full stop depending on the ISO rating (under) and that is enough to make for darker slides if I forget to adjust for it. Should really have sent it out for a CLA already...

Mainecoonmaniac · Dec 13, 2010

If you over expose slide film

stradibarrius said:
How much difference is there in the end result of slide vs. print film give todays available films?
Assuming the negatives are to be scanned and printed digitally opposed to needing slides for a presentation.

If you over expose slide film and blow out your highlights, you can't recover them. If you over expose color neg film, you might be able to recover highlight info.

benjiboy · Dec 13, 2010

I haven't processed E6 for about twenty years because for what it costs to have E6 processed in two hours at a local pro lab while I do my shopping it's not worth the hassle, and their machines do it better.

bblhed · Dec 13, 2010

I use the freestyle kit to process E-6 for Stereo slides and about the hardest part is warming up the chemicals. I have never done C-41 so I don't know what it looks like wet, but when you pull your E-6 out of the tank you have to believe that you didn't do anything wrong and just hang it up to dry and just believe it will not look like that when it dries. It is amazing but your film will look like the emulation was unaffected by processing and then slowly it will start to look like slide film with photos on it. Watching the drying process the first time is like watching magic.

First attempt at processing color slide film????

Privacy & Transparency

Privacy & Transparency