Durst M605 Colour europlug replacement possible?

Flannigan's Pass

A
Flannigan's Pass

  • 0
  • 1
  • 19
Out Houses

D
Out Houses

  • 3
  • 0
  • 18
Simply leaves

H
Simply leaves

  • 2
  • 1
  • 32

Forum statistics

Threads
198,981
Messages
2,784,051
Members
99,761
Latest member
Hooper
Recent bookmarks
0

djb070_4

Member
Joined
Jun 25, 2024
Messages
3
Location
UK
Format
Medium Format
Firstly hi everyone. First post here as relatively new to the enlarger / printing world - Its a steep learning curve ahead.

I'm here looking for some advice that I couldn't find on previous threads.

I recently purchased a Durst M605 colour enlarger with a TRA305N transformer. I also have a Paterson 2000D timer. The transformer has a flat europlug 2 pin lead but the timer has a UK C14 kettle socket. The transformer appears to be double insulated so am I safe to just cut the transformer wire and connect the L & N wires to the kettle plug provided by Paterson missing out the earth or am I safer to find adapters? I can't seem to track down a europlug > C14 adapter but I can get a euro > 3 pin plug adapter and then a 3 pin socket > kettle adapter which in theory would do the job!

Has anyone any experience of doing this and lived to tell the tale? Or should I just persuade an electrician to look at it...

Any thoughts welcome.

Thanks.
 

RalphLambrecht

Subscriber
Joined
Sep 19, 2003
Messages
14,657
Location
K,Germany
Format
Medium Format
Firstly hi everyone. First post here as relatively new to the enlarger / printing world - Its a steep learning curve ahead.

I'm here looking for some advice that I couldn't find on previous threads.

I recently purchased a Durst M605 colour enlarger with a TRA305N transformer. I also have a Paterson 2000D timer. The transformer has a flat europlug 2 pin lead but the timer has a UK C14 kettle socket. The transformer appears to be double insulated so am I safe to just cut the transformer wire and connect the L & N wires to the kettle plug provided by Paterson missing out the earth or am I safer to find adapters? I can't seem to track down a europlug > C14 adapter but I can get a euro > 3 pin plug adapter and then a 3 pin socket > kettle adapter which in theory would do the job!

Has anyone any experience of doing this and lived to tell the tale? Or should I just persuade an electrician to look at it...

Any thoughts welcome.

Thanks.

Sure, talk to an electrician, but be aware, that any reasonable electrician will advise against a two -pin setup bypassing earth! The flat europlug 2-pin lead is designed for very low-power applications or equipment not requiring earthing,such as concealed equipment with a plastic housing.
 

garry611

Member
Joined
Jan 24, 2005
Messages
13
Format
Med. Format Pan
Having spent some time in Europe, without a photo, it sounds as if the two pin plug is basically the equivalent to a US non-polarized plug. That is because it can be plugged in in either direction and a ground is not required. I would connect the transformer to the load and neutral wires of the kettle plug and not use the ground at all. The transformer is probably at neutral ground already. If you use the ground wire there is a possibility of creating a ground loop if the wall socket happened to be wired incorrectly.
 

koraks

Moderator
Moderator
Joined
Nov 29, 2018
Messages
23,074
Location
Europe
Format
Multi Format
The transformer is probably at neutral ground already

The primary of the transformer will be at whatever potential the incoming neutral is. I think in most countries in the world it's required that neutral is very close to earth/GND potential, but consult local code on this and measure if you want to be sure. The phase will evidently cycle around this by up to (+/-) 325V in the UK and Europe (230VAC).

The secondary of the transformer will be floating by definition, unless it's fixed at some potential, which is usually not the case; see below. The fact that the secondary of a transformer floats is actually a good thing from a safety viewpoint.

If you use the ground wire there is a possibility of creating a ground loop if the wall socket happened to be wired incorrectly.

No. Safety ground is not connected to the electrical circuit. It's connected to metal parts of the chassis and/or enclosure. Connecting safety ground to the electrical circuit will trip the earth leakage protection. Hence, the connection of a safety ground cannot and will not ever create a ground loop, at least in equipment made by anyone who knows what they're doing. It's a safety feature.

The iron core of the transformer is often connected to safety GND/earth, but the core has no electrical connection to the windings.

TRA305N transformer

AFAIK this has a plastic housing, so technically a safety ground is not even required, even by modern standards. You can connect a two-prong connector to this. If you open up the unit, you'll probably see that the GND doesn't go anywhere anyway, at least nothing particularly meaningful; maybe the xformer core; see note above.

Has anyone any experience of doing this and lived to tell the tale?

I've owned and repaired a fair number of Durst transformers and I have yet to come across one with a 3-prong cable. They all come with the standard 2-prong connectors that were standard decades ago.
 

Ian Grant

Subscriber
Joined
Aug 2, 2004
Messages
23,266
Location
West Midland
Format
Multi Format
Technically kettle leads and sockets are actually modified C14, with a ridge in the kettle socket, so that you have to use the dedicated higher power rated cable.

You need an IEC male C14 Power Inlet Connector 240v 10a Screw Terminal Kettle Cable Plug, any electrical store will sell them, also Amazon or B&Q (online only). You want the one with the round rubber, not figure of 8, cable protector.

I use them for as extension leads for my studio flash units.

Ian
 
OP
OP

djb070_4

Member
Joined
Jun 25, 2024
Messages
3
Location
UK
Format
Medium Format
Hi guys, thanks for all the responses. Apologies, it probably would've been clearer if I'd included photos first so here you go!

The first two are the transformer with a moulded 2 prong plug which I assume is a europlug but curiously the transformer seems to be to a BS standard? Either way I'm guessing it doesn't have a ground wire. The transformer is a plastic housing, as suggested, and has a double insulation mark on the label. The third/fourth photo is the timer with the socket on the LHS and as you can see I have a 'kettle' lead adapter to take wiring. I guess the crux of my question is, can I cut the transformer plug off and wire it in to the kettle adapter or do I have to look at a complicated set of adapters / new transformer?

Apologies for the dumb questions but I'm not an electrical genius as you can probably tell. Just don't want to start cutting things and do some irreparable damage to the enlarger. Or me.

Again any further advice appreciated.

D
 

Attachments

  • 1000012583.jpg
    1000012583.jpg
    881.3 KB · Views: 41
  • 1000012584.jpg
    1000012584.jpg
    484 KB · Views: 40
  • 1000012585.jpg
    1000012585.jpg
    916.9 KB · Views: 45
  • 20240626_175454.jpg
    20240626_175454.jpg
    717.5 KB · Views: 40
Last edited:

koraks

Moderator
Moderator
Joined
Nov 29, 2018
Messages
23,074
Location
Europe
Format
Multi Format
You can wire those up in any responsible way you prefer. Just connect only L and N, and leave safety GND disconnected. I'd take a trip to the local hardware store. Personally I prefer to keep the original connectors in place and buy or make an adapter.
 
OP
OP

djb070_4

Member
Joined
Jun 25, 2024
Messages
3
Location
UK
Format
Medium Format
You can wire those up in any responsible way you prefer. Just connect only L and N, and leave safety GND disconnected. I'd take a trip to the local hardware store. Personally I prefer to keep the original connectors in place and buy or make an adapter.

Thanks Koraks. Yes, adapters may be the best way, at least at first. Unfortunately can't seem to get a single adapter that'll take the europlug straight to the kettle socket so will need to use the two step approach I think. Failing that I'll try rewiring. What's the worst that can happen!

Anyway, thanks for your help.

D
 

triman

Member
Joined
Apr 18, 2008
Messages
3
Location
Ireland
Format
35mm
Would this work for you: Cerraxian C14 to C13 and Euro Y splitter power cable IEC14 male to IEC 13 female and euro CEE7/16 female extension cable on Amazon.de
 
Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links.
To read our full affiliate disclosure statement please click Here.

PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Ilford ADOX Freestyle Photographic Stearman Press Weldon Color Lab Blue Moon Camera & Machine
Top Bottom