Found Darkroom supplies for 8x10 contact printing

Trader history for blee1996 (13)

blee1996

Subscriber
Allowing Ads
Joined
Jul 25, 2008
Messages
1,399
Location
SF Bay Area, California
Format
Multi Format
Hi, I'm looking for essentials to start contact printing at home. I'm based in SF Bay Area.

1) 8x10 contact printing frame
2) Paper safe
3) Ilford Multi-Grade filter set
4) Development trays, tongs, and squeegees
5) Print washer
6) Print dryer
 

glbeas

Member
Allowing Ads
Joined
Sep 25, 2002
Messages
3,954
Location
Marietta, Ga. USA
Format
Multi Format
When I first started developing I used whatever I had and it worked. A vegetable bin for developer tray, an old pane of glass for contact prints, rinse in the sink. I cut a red lens from a car taillight to fit an old military flashlight. Contact printing is about as low tech as photographic darkroom work gets.
Enjoy!
 

Rick A

Subscriber
Allowing Ads
Joined
Mar 31, 2009
Messages
10,002
Location
Laurel Highlands
Format
8x10 Format
Go to a Dollar store and buy a one gallon plastic pitcher, 5 matching four cup measuring cups, three or four flat bottom plastic bins of at least 11x14 inches, and a box of nitrile gloves. This is your processing gear for prints and negatives. Buy a couple of cheap picture frames, toss the frames and use the glass for contact printing. Use RC paper so you don't need print a washer or dryer, and you really don't need a paper safe. Window squeegee from the dollar store. You don't say what you're using for a light source, so what do you really need for MG filters? Plan on spending about $30-$40 at the dollar store, the rest can be had on eBay or CraigsList.
 

MattKing

Moderator
Moderator
Allowing Ads
Joined
Apr 24, 2005
Messages
54,586
Location
Delta, BC Canada
Format
Medium Format
@Rick A 's suggestions are great, but I'll put in a vote for a paper safe as a really good, as soon as practical investment.
All you need to do is ruin one package of paper due to not closing it when you should, and you will understand!

I use LP record storage racks from the thrift store to dry my RC prints.
These sort:
 

Shaps

Subscriber
Allowing Ads
Joined
Mar 29, 2024
Messages
90
Location
Hawaii
Format
Medium Format
For contact printing I have always gone to a glass shop and bought a thick piece of window glass cut to 11x14 inches AND had them smooth all sides so I would not cut myself handling it.
 

Rick A

Subscriber
Allowing Ads
Joined
Mar 31, 2009
Messages
10,002
Location
Laurel Highlands
Format
8x10 Format
I should have added thrift stores and charity shops are your friends.
 
OP
OP

blee1996

Subscriber
Allowing Ads
Joined
Jul 25, 2008
Messages
1,399
Location
SF Bay Area, California
Format
Multi Format
I got everything sorted by a combination of DIY, re-use existing stuff, and buy a few essentials.

Here is the light source made from a clamp desk light fixture, 7.5w incandescent bulb, Lee filter holder. It worked very well and give me control over grades as well as exposure time of about 20s range. And if the negative is too thin, I add 0.3 ND filter for 1 stop. So far the prints look good.

Assemble the material:



And the final product:

 
Last edited:

AnselMortensen

Subscriber
Allowing Ads
Joined
Jun 9, 2020
Messages
2,703
Location
SFBayArea
Format
Traditional
Very clever, repurposing the desk lamp for contact printing by adding the filter holder!
 
You must log in or register to reply here.
Menu
Log in
Register