My eye-level prism's mirror is apparently loose (rattles when shaken) (not stirred). Can anyone share any repair ideas or info on how the mirror is shimmed or attached?
Bronica prism loose mirror?
-
A
- Thread starter rickbraun
- Start date
Recent Classifieds
-
For Sale ORIGINAL ROLLEIFLEX LENS SHADE
- Started by Philippe-Georges
-
For Sale T-max 4x5 100 kodak ready loads. expired 2008, kept frozen
- Started by Early Riser
-
For Sale Images in Science, excellent scientific imaging. $10
- Started by laser
-
Sold Book: PhotoShop Restoration and Retouching. $20
- Started by laser
Forum statistics
What kind of Bronica? There are several and the prisms are not all the same.
If it's an ETRS or SQ, the first things I would check are:
- Make sure the eyepiece lens hasn't come loose from its mount and fallen inside.
- If you remove the cover of the prism (screws on sides), the prism is usually held down by a plastic form. like a strap, with some foam and then a plastic shield between the foam and the glass (thank you Bronica; this prevents the foam from damaging the reflective coating). If the foam has deteriorated or the prism is loose for whatever reason, you can stuff some new foam or other shim material in between the shield and hold-down strap, and that should keep the prism from sliding forward once reassembled.
This is fairly simple for non-metered prisms. It might be similar for metered prisms but I haven't taken one apart.
If it's an ETRS or SQ, the first things I would check are:
- Make sure the eyepiece lens hasn't come loose from its mount and fallen inside.
- If you remove the cover of the prism (screws on sides), the prism is usually held down by a plastic form. like a strap, with some foam and then a plastic shield between the foam and the glass (thank you Bronica; this prevents the foam from damaging the reflective coating). If the foam has deteriorated or the prism is loose for whatever reason, you can stuff some new foam or other shim material in between the shield and hold-down strap, and that should keep the prism from sliding forward once reassembled.
This is fairly simple for non-metered prisms. It might be similar for metered prisms but I haven't taken one apart.
A trip to KEH could get that mirror fastened down before it chips, cracks or breaks.
Bronica ETR non-metered prism. Having a difficult time removing the screws. Probably need to purchase better set of mini-phillips driver set. Any recommendations on those? Thanks for taking the time to respond.
Do NOT use phillips bits. You really do need JIS (Japanese Industry Standard) bits. Regular phillips drivers will chew the screw, which is an unfortunate rhyme.
Personally, I love my iFixit Pro kit-- it meets about 95% of the needs for disassembling cameras, and it includes four JIS driver bits.
I'll get a set and investigate. Thanks
There are sets made by Vessel that include various JIS screwdrivers that are pretty good price and easy to get on ebay or elsewhere. You likely need a #0 driver. Using a too-small driver will damage cross-point screws.
This page explains the difference between JIS and Phillips: https://www.vesseltools.com/handtools/screwdrivers/jis-japanese-industrial-standard
IME, the screws in the Bronica prism were not as unreasonably tight as some camera screws I have seen, and a good #0 Phillips driver would work if you have a careful hand. However, YMMV. Emphasis on good as there are a lot of cheap but low quality "precision" screwdrivers out there.
I think you need to take out about four screws to remove the prism cover, two in the front sides and two near the rear, but can't remember exactly where and I'm not near an ETRS at the moment. It wasn't too hard to figure out.
This page explains the difference between JIS and Phillips: https://www.vesseltools.com/handtools/screwdrivers/jis-japanese-industrial-standard
IME, the screws in the Bronica prism were not as unreasonably tight as some camera screws I have seen, and a good #0 Phillips driver would work if you have a careful hand. However, YMMV. Emphasis on good as there are a lot of cheap but low quality "precision" screwdrivers out there.
I think you need to take out about four screws to remove the prism cover, two in the front sides and two near the rear, but can't remember exactly where and I'm not near an ETRS at the moment. It wasn't too hard to figure out.
Update - purchased a set of JIS screwdrivers - worked like a charm to remove the 2 screws on each side of the prism cover. Internally, there is a cork pad, which had deteriorated. Applied a few layers of duck tape over the pad to increase its thickness (thus lessening the distance between the pad and the cover. Perfect fix - thanks to everyone for your responses and help.
Maybe of help:
www.photrio.com
Rollei 45 degree Prism Repair
I have had this 45 degree prism since about 1993. Recently it sounded loose, and the glass is rattling around.
www.photrio.com
| Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links. To read our full affiliate disclosure statement please click Here. |
PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:  |