Adjusting focus on hasselblad

Ford Trimotor

A
Ford Trimotor

  • 0
  • 0
  • 16
museum

A
museum

  • 3
  • 1
  • 60
Old Willow

H
Old Willow

  • 0
  • 2
  • 90
SteelHead Falls

A
SteelHead Falls

  • 8
  • 0
  • 102

Recent Classifieds

Forum statistics

Threads
198,133
Messages
2,770,134
Members
99,566
Latest member
ATX_BW_Arch
Recent bookmarks
0

dfoo

Member
Joined
Mar 28, 2008
Messages
268
Format
Medium Format
I did some test shots yesterday with my 150mm lens wide open. Examining the negatives with a loupe shows that either the lens is simply not very sharp at F4, or the focus was off. The focus point was about 6-7 feet away. I took some later shots at F32 and the object is very focused. I'm using a split-prism screen, using the focusing magnifier on the waist level finder. Is this just not accurate enough for such precise focusing, is the focus off? Is the lens not sharp? Is there a way to adjust the focus?
 

archphoto

Member
Joined
Dec 14, 2008
Messages
960
Location
Holland and
Format
4x5 Format
The best way is to photograph a tape measure on the ground under an angle.

Focus on one point and write down.

If your focus is off then you will see how much.

Peter
 
OP
OP

dfoo

Member
Joined
Mar 28, 2008
Messages
268
Format
Medium Format
If the focus is off how do you adjust it?
 

bdial

Subscriber
Joined
Jan 2, 2005
Messages
7,449
Location
North East U.S.
Format
Multi Format
What body do you have? On 500C's the positioning of the screen can be adjusted with shims, I believe.
For the newer ones, I am not sure.
 

John Koehrer

Subscriber
Joined
Apr 3, 2004
Messages
8,275
Location
Aurora, Il
Format
Multi Format
The first thing you need to do is check infinity focus. If that's on everything else is. Pick a target around 500-1000 feet away, that's enough for practical purposes.
Check focus at BOTH the focusing screen and the film plane. Use a piece of ground glass for the film plane.
If they're the same, it's not the camera. If their different the plane of the screen needs to be adjusted. On the CM I'm not sure but on the C you had to remove the screen & fiddle with four adjustment screws beneath the screen.
 
OP
OP

dfoo

Member
Joined
Mar 28, 2008
Messages
268
Format
Medium Format
I just did a quick test. I focused at 3 meters through the lens & screen at F4. I then opened the shutter, took the focus screen and placed in at the back of the camera, and looked at the split prism. It was around 50cm off according to the focus scale on the lens. I'm not sure where the exact film plane is supposed to be, but I would guess it is pretty close to where i had the screen. What would be simplest would be to shim the screen slightly. The screen rests on 4 posts, but there doesn't appear to be an easy way to adjust the height of those posts. Any ideas?
 

Q.G.

Member
Joined
Jul 23, 2007
Messages
5,535
Location
Netherlands
Format
Medium Format
It is unlikely that the focussing screen seat is to blame.

The mirror can be off, needing the pads it sits on replaced for new ones.

Could also be the body length. But unless you dropped the camera, or disassembled the thing and not put it back right again, not likely.

I would ask a repair shop to replace the mirror pads and realign the thing.
 
OP
OP

dfoo

Member
Joined
Mar 28, 2008
Messages
268
Format
Medium Format
Mm... where are the pads? The mirror in my camera sits on two metal brackets.
 

Q.G.

Member
Joined
Jul 23, 2007
Messages
5,535
Location
Netherlands
Format
Medium Format
That repair manual is for cameras with a slightly different construction.

The pads below the 500 C/M's mirror are shown in the image below (no. 4, sitting in the pan 3, below the mirror 5):
Mirrorpads.jpg


Foam pads deteriorate, and they would be the first thing i would look at.

If the pads are not to blame, there is a lot else to adjust.
All of this should be done using the proper jigs and know-how. So better ask a qualified repair person.
 

mike c

Subscriber
Joined
Jan 5, 2009
Messages
2,863
Location
Los Angeles
Format
Multi Format
dfoo, last time I was in to my camera repair place at samys I told him I was buying a accu screen for my cm,he told me stop by after I bought it so he could check the focus. So I did he put it in some can of Jig,made some kind of measurements an it was fine.Took him 10 min and didn't charge a penny. Although I had recently had him do a CLR. It might be cheaper in the long run to have a good tech have a look at it. I would diffidently try the tape measure thing with flim in camera,also the infinity test.
 
Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links.
To read our full affiliate disclosure statement please click Here.

PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Ilford ADOX Freestyle Photographic Stearman Press Weldon Color Lab Blue Moon Camera & Machine
Top Bottom