Formula for development time temperature adjustment?

Forum statistics

Threads
177,133
Messages
2,429,999
Members
94,143
Latest member
helimat
Recent bookmarks
0

ged

Member
Joined
Jun 18, 2003
Messages
42
Location
Sydney, Aust
Shooter
35mm
On the Ilford website and various other sources, you can find a graph for determining film development time at different temperatures. This is often difficult to use since my starting time may include a fraction of a minute or the temperature of my tap water wanders off the range of the graph.

Does anyone have the formula from which the graph was derived? Thanks in advance!
 

Mateo

Member
Joined
Sep 7, 2002
Messages
505
Location
Hollister, C
Shooter
Multi Format
Each developer I think would have a different rate of adjustment so I doubt there is a formula that exactly meets your needs. But what you might want to look at is the temps that wanders off the range. Temps effect the reducing agents at different rates so that unless you've got a specific reason for straying too far from 68deg, it's worth while to try to standardize. I don't use tap water so my bottles of distilled water normally pour out at exactly 70degs and that's my standard. I hope this helps.
 

Ole

Moderator
Moderator
Joined
Sep 9, 2002
Messages
9,250
Location
Bergen, Norway
Shooter
Large Format
The ranges presented in the graphs are the ranges where the developer will behave reasonably correctly. If your temperatures are out of hte graph range, you must change either the temperature or hte developer!
 
OP
OP

ged

Member
Joined
Jun 18, 2003
Messages
42
Location
Sydney, Aust
Shooter
35mm
Thanks for the replies. Even within the range of graph, I find that using the graph is a bit clumsy and would prefer to use a formula if one exists.

Ole: My water temperature went out of range (26C) on a particularly hot day. I should probably try a cold water bath next time to keep it in range.

Mateo: I don't recall the Ilford site mentioning that the graph is dependent on the type of developer. I will have to check that.
 

Donald Miller

Member
Joined
Dec 21, 2002
Messages
6,233
Shooter
Large Format
I use the Zone VI compensating development timer. It has curves for both paper and film and seems to work fairly accurately in my experience.
 
Joined
Jun 9, 2003
Messages
614
Location
Brazil
Shooter
35mm
I saw it on the NET - and remember clearly a graph was drawn form the median of Kodak and Ilford numbers...
 
OP
OP

ged

Member
Joined
Jun 18, 2003
Messages
42
Location
Sydney, Aust
Shooter
35mm
Don: Buying a timer for this is not really an option until I setup a darkroom. It's good to know that the Zone VI timer can be used for temperature compensation though.

Jorge: Thanks for the link. I tried a few values and although some were quite accurate, others were noticeably off. I think I'll try to contact the author to find out where the formula came from.
 
Joined
Jun 9, 2003
Messages
614
Location
Brazil
Shooter
35mm
Ged

A much better one:

Dead Link Removed
 

john_s

Subscriber
Joined
Nov 19, 2002
Messages
1,627
Location
Melbourne, A
Shooter
Medium Format
The Ilford graphs are "one size fits all" and are approximations. (ok, I know that *everything* in photography is an approximation).

There is a simple formula that you can use if you have two time+temperature points, e.g. of the sort often published by manufacturers.

I can send you a small Excel spreadsheet if you would like it. Email me at j.sto@bigpond.com
 
Photrio.com contains affiliate links to products. We may receive a commission for purchases made through these links.
To read our full affiliate disclosure statement please click Here.

PHOTRIO PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Ilford Photo ADOX Freestyle Photographic Photo Warehouse Stearman Press Weldon Color Lab
Top Bottom